Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM B837-01

Standard Specification for Seamless Copper Tube for Natural Gas and Liquefied Petroleum (LP) Gas Fuel Distribution Systems

Automaticky preložený názov:

Štandardné špecifikácie pre bezšvíkové medené rúrky pre zemný plyn a skvapalnený ropný ( LP ) , plynné palivá distribučných systémov

NORMA vydaná dňa 10.10.2001

Jazyk
Prevedenie	Online zabezpečené PDF - 76.70 € Tlačené - 76.70 €
Dostupnosť	SKLADOM
Cena	76.70 € bez DPH
76.70 €

Informácie o norme:

Označenie normy: ASTM B837-01
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.10.2001
Kód tovaru: NS-8344
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM B837-01 :

Keywords:

brazed joints, C12200, flared fittings, fuel distribution systems, liquefied petroleum (LP) gas, natural gas, seamless copper tube, ICS Number Code 75.200 (Petroleum products and natural gas handling equipment)

Doplňujúce informácie

1. Scope

1.1 This specification establishes the requirements for Type GAS seamless Copper UNS No. C12200 tube for use in above ground natural gas and liquefied petroleum (LP) gas fuel distribution systems, commonly assembled with flared fittings or brazed joints.

1.2 O60 (soft annealed) temper gas tube is produced in the range of standard sizes 3/8- to 7/8-in. outside diameter; H58 (drawn general purpose) temper gas tube is produced in the range of standard sizes 3/8- to 11/8-in. outside diameter.

1.3 O60 (soft annealed) temper gas tube systems are normally assembled with single 45 flared fittings, although brazed connections using wrought or cast fittings may be permitted by local or code requirements. H58 (drawn general purpose) temper gas tube systems are assembled with brazed connections.

Note 1—Tube temper and applicable size are determined by installation code requirements.

1.4 Flared fittings used with seamless copper tube for natural gas and liquified petroleum (LP) gas fuel distribution systems shall be free of residual stresses.

1.5 The values stated in inch-pound units are standard. SI values given in parentheses are for information only.

2. Referenced Documents

E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
B846-24	Standard Terminology for Copper and Copper Alloys
E243-24	Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
B601-24	Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast
B153-22	Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
E8-04	Standard Test Methods for Tension Testing of Metallic Materials
E3-26	Standard Guide for Preparation of Metallographic Specimens
E112-25e1	Standard Test Methods for Determining Average Grain Size (Includes all amendments and changes 9/9/2026).
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E53-07	Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E18-25	Standard Test Methods for Rockwell Hardness of Metallic Materials

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.