Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM B804-02(2013) 1.2.2013 náhľad

Doplňujúce informácie

ASTM B804-02(2013)

Standard Specification for UNS N08367 and UNS N08926 Welded Pipe

Automaticky preložený názov:

Štandard Specification pre UNS N08367 a UNS N08926 zvárané rúry

NORMA vydaná dňa 1.2.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.00 € Tlačené - 70.00 €
Dostupnosť	SKLADOM
Cena	70.00 € bez DPH
70.00 €

Informácie o norme:

Označenie normy: ASTM B804-02(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.2.2013
Kód tovaru: NS-8200
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Výrobky z niklu a chrómu

Anotácia textu normy ASTM B804-02(2013) :

Keywords:
UNS N08367, welded pipe, ICS Number Code 77.150.40 (Nickel and chromium products)

Doplňujúce informácie

1. Scope

1.1 This specification covers UNS N08367 and UNS N08926 welded pipe for general corrosion applications. (Although no restrictions are placed on the sizes of pipe that may be furnished under this specification, commercial practice is commonly limited to sizes not less than 8 in. nominal diameter.)

1.2 Six classes of pipe are covered as follows:

1.2.1 Class 1 pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed.

1.2.2 Class 2 pipe shall be double welded by processes employing filler metal in all passes. No radiography is required.

1.2.3 Class 3 pipe shall be double welded by processes employing filler metal in all passes except the inside root weld may be made without the addition of filler metal. Welds are to be completely radiographed.

1.2.4 Class 4 pipe shall be double welded by processes employing filler metal in all passes except the inside root weld may be made without the addition of filler metal. No radiography is required.

1.2.5 Class 5 pipe shall be single welded by processes employing filler metal in all passes except that the pass exposed to the inside pipe surface may be made without the addition of filler metal. Welds are to be completely radiographed.

1.2.6 Class 6 pipe shall be single welded by processes employing filler metal in all passes except that the pass exposed to the inside pipe surface may be made without the addition of filler metal. No radiography is required.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this standard: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

E38-85	Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys (Withdrawn 1989)
A262-15(2021)	Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
B899-21	Standard Terminology Relating to Non-ferrous Metals and Alloys
B880-14(2019)	Standard Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
B688-22	Standard Specification for Chromium-Nickel-Molybdenum-Iron Plate, Sheet, and Strip
B625-21	Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloy, Ni-Fe-Cr-Si Alloy, Cr-Ni-Fe-N Low-Carbon Alloy, Fe-Ni-Cr-Mo-Cu-N Alloy, and Ni-Fe-Cr-Mo-N Alloy Plate, Sheet, and Strip
E1473-22	Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys
E1019-18	Standard Test Methods for Determination of Carbon, Sulfur, Nitrogen, and Oxygen in Steel, Iron, Nickel, and Cobalt Alloys by Various Combustion and Inert Gas Fusion Techniques
A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products
E8-04	Standard Test Methods for Tension Testing of Metallic Materials
E354-21e1	Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys (Includes all amendments and changes 2/23/2022).