Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM B75/B75M-19 1.4.2019 náhľad

Doplňujúce informácie

ASTM B75/B75M-19

Standard Specification for Seamless Copper Tube

NORMA vydaná dňa 1.4.2019

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 74.70 € Tlačené - 74.70 €
Dostupnosť	SKLADOM
Cena	74.70 € bez DPH
74.70 €

Informácie o norme:

Označenie normy: ASTM B75/B75M-19
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2019
Kód tovaru: NS-948729
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Výrobky z mědi

Anotácia textu normy ASTM B75/B75M-19 :

Keywords:

seamless copper tube, seamless tube, tube, C10100, C10200, C10300, C10800, C12000, C12200,, ICS Number Code 77.150.30 (Copper products)

Doplňujúce informácie

1. Scope

1.1 This specification2 establishes the requirements for seamless round, rectangular, and square copper tube suitable for general engineering applications.

1.1.1 Tubes made from any of the following Copper UNS No. designations shall be supplied unless otherwise specified in the contract or purchase order:

Copper UNS No.

Type of Copper

C10100

Oxygen-free electronic

C10200

Oxygen-free without residual deoxidants

C10300

Oxygen-free, extra low phosphorus

C10800

Oxygen-free, low phosphorus

C12000

Phosphorus deoxidized, low residual phosphorus

C12200

Phosphorus deoxidized, high residual phosphorus

1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.3 The following safety hazard caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

B170-99(2020)	Standard Specification for Oxygen-Free Electrolytic Copper´Refinery Shapes
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
B251-10	Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube
E8/E8M-24	Standard Test Methods for Tension Testing of Metallic Materials
B153-22	Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
B251M-10	Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube [Metric] (Withdrawn 2017)
B577-19	Standard Test Methods for Detection of Cuprous Oxide (Hydrogen Embrittlement Susceptibility) in Copper
B601-18a	Standard Classification for Temper Designations for Copper and Copper Alloys´Wrought and Cast (Includes all amendments and changes 10/24/2018).
B846-19a	Standard Terminology for Copper and Copper Alloys (Includes all amendments and changes 8/8/2019).
E3-11(2017)	Standard Guide for Preparation of Metallographic Specimens
E53-07	Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E112-13(2021)	Standard Test Methods for Determining Average Grain Size
E243-18	Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
E18-22	Standard Test Methods for Rockwell Hardness of Metallic Materials
E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
B193-20	Standard Test Method for Resistivity of Electrical Conductor Materials

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.