Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM B608-11

Standard Specification for Welded Copper-Alloy Pipe

Automaticky preložený názov:

Štandardné podmienky pre zvárané oceľové rúrky zo zliatin medi

NORMA vydaná dňa 1.10.2011

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 76.10 € Tlačené - 76.10 €
Dostupnosť	SKLADOM
Cena	76.10 € bez DPH
76.10 €

Informácie o norme:

Označenie normy: ASTM B608-11
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2011
Kód tovaru: NS-7384
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Výrobky z mědi

Anotácia textu normy ASTM B608-11 :

Keywords:

copper-alloy pipe, welded copper-alloy pipe, welded pipe, UNS No. C61300, UNS No. C61400, UNS No. C70620, UNS No. C71520: Aluminum bronzes--specifications, Brackish water/brines, Bronze pipe/tube--specifications, Copper alloy pipe--specifications, Seawater (natural/synthetic), UNS C61300 (aluminum bronze)--pipe/tube, UNS C61400 (aluminum bronze D)--pipe/tube, UNS C70600 (Cu-Ni)--pipe/tube (seamless/welded), UNS C71500--pipe/tube (seamless/welded), Welded Cu/Cu alloy pipe

Doplňujúce informácie

Significance and Use

For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.

Property	Rounded Unit for Observed or Calculated Value

Chemical composition	nearest unit in the last right-hand significant digit used in expressing the limiting value
Tensile strength	nearest ksi (5 MPa)

1. Scope

1.1 This specification establishes the requirements for arc-welded pipe for use in brackish water or seawater piping systems.

1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following hazard statement pertains only to the test method described in 8.2 and 14.3.2 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

E76-88(1998)	Standard Test Methods for Chemical Analysis of Nickel-Copper Alloys (Withdrawn 2003)
E190-21	Standard Test Method for Guided Bend Test for Ductility of Welds
B171/B171M-18	Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers
B846-19a	Standard Terminology for Copper and Copper Alloys (Includes all amendments and changes 8/8/2019).
E478-08(2017)	Standard Test Methods for Chemical Analysis of Copper Alloys
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
B169/B169M-20	Standard Specification for Aluminum Bronze Sheet, Strip, and Rolled Bar
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E8-04	Standard Test Methods for Tension Testing of Metallic Materials