Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube
NORMA vydaná dňa 1.10.2018
Označenie normy: ASTM B543/B543M-18
Dátum vydania normy: 1.10.2018
Kód tovaru: NS-904412
Počet strán: 12
Približná hmotnosť: 36 g (0.08 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
This specification covers welded tube of specific copper and various copper alloys of a limited range of diameters, for use in surface condensers, evaporators, heat exchangers, and general engineering applications. The product shall be manufactured by forming the material into a tubular shape on a suitable forming mill. Welding of tube shall be accomplished by forge-welding, fusion-welding, or full finishing that produces a forge weld leaving no crevice in the weld seam visible to the unaided eye. The tube shall conform to tensile strength and yield strength requirements, and shall be subject to expansion, flattening, and reverse bend tests. Mercurous nitrate or ammonia vapor tests shall be required only for selected UNS Numbers of Copper Alloys. Each tube shall be subjected to eddy-current, hydrostatic, and pneumatic tests.
Keywords:
condenser, copper, copper alloy, copper nickel, evaporator, heat exchanger, welded tube, UNS No. C10800, UNS No. C12200, UNS No. C19400, UNS No. C23000, UNS No. C44300, UNS No. C44400, UNS No. C44500, UNS No. C68700, UNS No. C70400, UNS No. C70600, UNS No. C70620, UNS No. C71000, UNS No. C71500, UNS No. C71520, UNS No. C71640, UNS No. C72200,, ICS Number Code 77.150.30 (Copper products)
Significance and Use | ||||||||||||
20.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
|
||||||||||||
1. Scope | ||||||||||||
1.1 This specification establishes the requirements for welded tube of copper and various copper alloys up to 31/8 in., inclusive, in diameter, for use in surface condensers, evaporators, heat exchangers, and general engineering applications. The following coppers or copper alloys are involved: Copper or |
Previously Used |
Type of Metal |
||||||||||
C10800A |
... |
oxygen-free, low phosphorus |
||||||||||
C12200A |
... |
DHP phosphorized, high |
||||||||||
C19400 |
... |
copper-iron alloy |
||||||||||
C23000 |
... |
red brass |
||||||||||
C44300 |
... |
arsenical admiralty |
||||||||||
C44400 |
... |
antimonial admiralty |
||||||||||
C44500 |
... |
phosphorized admiralty |
||||||||||
C68700 |
... |
arsenical aluminum brass |
||||||||||
C70400 |
... |
95-5 copper-nickel |
||||||||||
C70600 |
... |
90-10 copper-nickel |
||||||||||
C70620 |
... |
90-10 copper-nickel (Modified |
||||||||||
C71000 |
... |
80-20 copper-nickel |
||||||||||
C71500 |
... |
70-30 copper-nickel |
||||||||||
C71520 |
... |
70-30 copper-nickel (Modified |
||||||||||
C71640 |
... |
copper-nickel-iron-manganese |
||||||||||
C72200 |
... |
... |
1.2 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
(Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002) |
|
Standard Classification of Coppers |
|
Standard Test Method for Mercurous Nitrate Test for Copper Alloys |
|
Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing |
|
Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
|
Standard Test Methods for Tension Testing of Metallic Materials |
|
Standard Guide for Preparation of Metallographic Specimens |
|
Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
|
Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition |
|
Standard Test Methods for Chemical Analysis of Copper Alloys |
|
Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes |
|
Standard Test Methods for Chemical Analysis of Copper-Chromium Alloys |
|
Standard Test Methods for Determining Average Grain Size |
|
Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) |
|
Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube |
|
Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies |
|
Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys |
|
Standard Terminology for Copper and Copper Alloys (Includes all amendments and changes 8/8/2019). |
|
Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry |
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-09-11 (Počet položiek: 2 346 290)
© Copyright 2024 NORMSERVIS s.r.o.