Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM B359/B359M-02

Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins

Automaticky preložený názov:

Štandardné špecifikácie pre medi a zliatin medi Bezproblémová chladičom a výmenník tepla s integrovaným plutiev

NORMA vydaná dňa 10.10.2002

Jazyk
Prevedenie	Online zabezpečené PDF - 81.60 € Tlačené - 81.60 €
Dostupnosť	SKLADOM
Cena	81.60 € bez DPH
81.60 €

Informácie o norme:

Označenie normy: ASTM B359/B359M-02
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.10.2002
Kód tovaru: NS-6378
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM B359/B359M-02 :

Keywords:

condenser, copper, copper alloys, heat exchanger, integral fins, seamless, tube, UNS No. C10100, UNS No. C10200, UNS No. C10300, UNS No. C10800, UNS No.C12000, UNS No.C12200, UNS No. C14200, UNS No. C19200, UNS No. C23000, UNS No. C44300, UNS No. C44400, UNS No. C44500, UNS No. C60800, UNS No. C68700, UNS No. C70400, UNS No. C70600, UNS No. C70620, UNS No. C71000, UNS No. C71500, UNS No. C71520, UNS No. C, ICS Number Code 23.040.15 (Non-ferrous metal pipes)

Doplňujúce informácie

1. Scope

1.1 This specification establishes the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a cold-forming process to produce an integral enhanced surface for improved heat transfer.

1.2 UnitsThe values stated in either in-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems could result in nonconformance with the specification.

1.3 The tubes are typically used in surface condensers, evaporators, and heat exchangers.

1.4 The product shall be produced of the following coppers or copper alloys, as specified in the ordering information.

Copper or Copper Alloy UNS No.	Type of Metal

C10100	Oxygen-free electronic
C10200	Oxygen-free without residual deoxidants
C10300	Oxygen-free, extra low phosphorus
C10800	Oxygen-free, low phosphorus
C12000	DLP Phosphorized, low residual phosphorus (See Note 1)
C12200	DHP, Phosphorized, high residual phosphorus (See NOTE 1)
C14200	DPA Phosphorized arsenical (See NOTE 1)
C19200	Phosphorized, 1 % iron
C23000	Red Brass
C44300	Admiralty Metal Types B,
C44400	C, and
C44550	D
C60800	Aluminum Bronze
C68700	Aluminum Brass Type B
C70400	95-5 Copper-Nickel
C70600	90-10 Copper-Nickel
C70620	90-10 Copper-Nickel (Modified for Welding)
C71000	80-20 Copper-Nickel Type A
C71500	70-30 Copper-Nickel
C71520	70-30 Copper-Nickel (Modified for Welding)
C72200	Copper-Nickel

Note 1—Designations listed in Classification B 224.

1.5 The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.6 Product produced in accordance with the Supplementary Requirements section for military applications shall be produced only to the inch-pound system of this specification.

2. Referenced Documents

B224-16(2022)	Standard Classification of Coppers
B601-24	Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast
B154-16(2022)	Standard Test Method for Mercurous Nitrate Test for Copper Alloys
B153-22	Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
E2575-19	Standard Test Method for Determination of Oxygen in Copper and Copper Alloys by Inert Gas Fusion
E478-24	Standard Test Methods for Chemical Analysis of Copper Alloys
E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E243-24	Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
E118-89(1996)	Standard Test Methods for Chemical Analysis of Copper-Chromium Alloys
E112-25	Standard Test Methods for Determining Average Grain Size
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E53-07	Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E8/E8M-25	Standard Test Methods for Tension Testing of Metallic Materials
E3-26	Standard Guide for Preparation of Metallographic Specimens
D4727/D4727M-22	Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes
B968/B968M-16(2022)	Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube
B900-16(2022)	Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies
B858-06(2024)	Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys
B846-24	Standard Terminology for Copper and Copper Alloys
B170-24	Standard Specification for Oxygen-Free Electrolytic Copper—Refinery Shapes

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.