Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM B250/B250M-13 1.4.2013 náhľad

Doplňujúce informácie

ASTM B250/B250M-13

Standard Specification for General Requirements for Wrought Copper Alloy Wire

Automaticky preložený názov:

Štandard Specification pre všeobecné požiadavky na zliatiny medi drôt zo zliatiny

NORMA vydaná dňa 1.4.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.10 € Tlačené - 70.10 €
Dostupnosť	SKLADOM
Cena	70.10 € bez DPH
70.10 €

Informácie o norme:

Označenie normy: ASTM B250/B250M-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2013
Kód tovaru: NS-5971
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Výrobky z mědi

Anotácia textu normy ASTM B250/B250M-13 :

Keywords:
copper-alloy wires, wires, wrought copper-alloy wires, flat wires, ICS Number Code 77.150.30 (Copper products)

Doplňujúce informácie

Significance and Use

12.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.

Property	Rounded Unit for Observed or Calculated Value

Dimensions Chemical composition Hardness Electrical resistivity/conductivity	nearest unit in the last right-hand significant digit used in expressing the limiting value

Tensile strength Yield strength	nearest ksi [5 MPa]

Elongation
Below 5 %	nearest multiple of 0.5 %
5 % and over	nearest 1 %

Grain size
Under 0.060 mm	nearest multiple of 0.005 mm
0.060 mm and over	nearest 0.01 mm

1. Scope

1.1 This specification establishes requirements common to wrought copper and copper alloy wire and shall apply to Specifications B16/B16M, B99/B99M, B134/B134M, B159/B159M, B197/B197M, B206/B206M, B272, B301/B301M, B453/B453M, B967/B967M, and B974/B974M to the extent referenced therein.

1.2 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification shall be prescribed in the product specification.

1.3 Units—Values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

E118-89(1996)	Standard Test Methods for Chemical Analysis of Copper-Chromium Alloys
E75-76(1996)	Standard Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E478-08(2017)	Standard Test Methods for Chemical Analysis of Copper Alloys
E581-17A(2022)e1	Standard Test Methods for Chemical Analysis of Manganese-Copper Alloys (Includes all amendments and changes 9/13/2022).
E121-83(1996)	Standard Test Methods for Chemical Analysis of Copper-Tellurium Alloys
E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E54-80(1996)	Standard Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E18-22	Standard Test Methods for Rockwell Hardness of Metallic Materials
E8/E8M-24	Standard Test Methods for Tension Testing of Metallic Materials
E3-11(2017)	Standard Guide for Preparation of Metallographic Specimens
B974/B974M-16(2021)	Standard Specification for Free-Cutting Bismuth Brass Rod, Bar and Wire
B967/B967M-18(2023)	Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
E112-13(2021)	Standard Test Methods for Determining Average Grain Size
B900-16(2022)	Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies
B194-22	Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar
B193-20	Standard Test Method for Resistivity of Electrical Conductor Materials
B159/B159M-17	Standard Specification for Phosphor Bronze Wire
B134/B134M-15(2021)	Standard Specification for Brass Wire
B99/B99M-15(2021)	Standard Specification for Copper-Silicon Alloy Wire for General Applications
B16/B16M-19	Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B206/B206M-12(2017)	Standard Specification for Copper-Nickel-Zinc (Nickel Silver) Wire and Copper-Nickel Alloy Wire
B846-19a	Standard Terminology for Copper and Copper Alloys (Includes all amendments and changes 8/8/2019).
B453/B453M-19	Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes
B197/B197M-20e1	Standard Specification for Copper-Beryllium Alloy Wire (Includes all amendments and changes 11/21/2022).
B272-12(2019)	Standard Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)
B301/B301M-13(2020)	Standard Specification for Free-Cutting Copper Rod, Bar, Wire, and Shapes