Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes (Includes all amendments and changes 6/30/2022).
NORMA vydaná dňa 1.11.2019
Označenie normy: ASTM B210/B210M-19a
Dátum vydania normy: 1.11.2019
Kód tovaru: NS-975381
Počet strán: 15
Približná hmotnosť: 45 g (0.10 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
This specification covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose. The tube shall be produced by drawing an extruded tube made from hollow extrusion ingot (cast in hollow form or pierced) and extruded by the use of the die and mandrel method. The tubes shall conform to the chemical composition requirements specified. The determination of chemical composition shall be made in accordance with suitable chemical (test methods E 34), or spectrochemical (test methods E 607 and E 1251), methods. The tube shall conform to the tensile property requirements specified. The tension tests shall be made in accordance with test methods B 557M. Flattening test specimens shall be flattened sidewise under a gradually applied load so as to give a uniform radius of bend until the minimum outside diameter under load is not more than F times the wall thickness of the tube as specified. The specimen shall be forced axially with steady pressure over a hardened and polished tapered steel pin having a 74? included angle, to produce a flare having the permanent expanded outside diameter specified. When specified, heat treatment of applicable tempers shall be in accordance with practice B 918. The different methods for leak testing of tubes are presented.
Keywords:
aluminum alloy, aluminum-alloy drawn seamless tubes,, ICS Number Code 77.150.10 (Aluminium products)
1. Scope | ||||||||||
1.1 This specification2 covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose and pressure applications in alloys (Note 2), tempers, and thicknesses shown in Table 2 [Table 3]. Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0.083 in. [2.00 mm] and only in non-heat-treatable alloys.
1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum designation 1100 in accordance with Practice E527. Note 1: See Specification B483/B483M for aluminum-alloy drawn tubes
for general purpose applications; Specification B234 for aluminum-alloy drawn seamless
tubes for condensers and heat exchangers; and Specification
B241/B241M for aluminum-alloy
seamless pipe and seamless extruded tube.
Note 2: Throughout this specification, use of the term
1.3 For acceptance criteria for inclusion
of new aluminum and aluminum alloys in this specification, see
Annex A2.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-09-08 (Počet položiek: 2 346 217)
© Copyright 2024 NORMSERVIS s.r.o.