Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM B179-18

Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes

NORMA vydaná dňa 15.5.2018

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 66.20 € PDF + redline - ihneď - 79.50 € Tlačené - 66.20 € Tlač + redline - 79.50 €
Dostupnosť	SKLADOM
Cena	66.20 € bez DPH
66.20 €

Informácie o norme:

Označenie normy: ASTM B179-18
Dátum vydania normy: 15.5.2018
Kód tovaru: NS-848400
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Výrobky z hliníku

Anotácia textu normy ASTM B179-18 :

This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The material shall be of uniform quality and shall be free from dross, slag, and other harmful contamination. The ingots or molten metal shall conform to the chemical composition limits specified.

Keywords:

aluminum, ingot, molten metal,, ICS Number Code 77.150.10 (Aluminium products)

Doplňujúce informácie

1. Scope

1.1 This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The specific gravity of these alloys does not exceed 3.0 and they are designated as shown in Table 1.

Note 1: Throughout this specification the use of “ingot” in a general sense includes sow, T-bar, T-ingot, and pig.

1.2 Alloy designations are in accordance with ANSI H35.1/H35.1(M).

Note 2: Supplementary data pertaining to the alloys covered by this specification when used in the form of castings are given in Specifications B26/B26M, B85/B85M, B108/B108M, B618/B618M, B686/B686M, B955/B955M, and B969/B969M.

1.3 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.

1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1.

1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

B686/B686M-18	Standard Specification for Aluminum Alloy Castings, High-Strength
B985-12(2016)	Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis
B955/B955M-18	Standard Specification for Aluminum-Alloy Centrifugal Castings
B969-10	Standard Specification for Aluminum-Alloy Castings Produced by the Squeeze Casting, Thixocast and Rheocast Semi-Solid Casting Processes
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34-11	Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E607-02	Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere
B26/B26M-18e1	Standard Specification for Aluminum-Alloy Sand Castings (Includes all amendments and changes 4/2/2021).
B85/B85M-18e1	Standard Specification for Aluminum-Alloy Die Castings (Includes all amendments and changes 4/2/2021).
E716-16(2021)e2	Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry (Includes all amendments and changes 9/7/2022).
E1251-17a	Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry (Includes all amendments and changes 10/26/2017).
H35.1/H35.1(M)	American National Standard Alloy and Temper Designation Systems for Aluminum Available from Aluminum Association, Inc., 1525 Wilson Blvd., Suite 600, Arlington, VA 22209, http://www.aluminum.org.
Designations and Chemical Composition Limits for Aluminum Alloys in the Form of Castings and Ingot	(The Pink Sheets)
B618/B618M-18e1	Standard Specification for Aluminum-Alloy Investment Castings (Includes all amendments and changes 4/2/2021).
B108/B108M-19	Standard Specification for Aluminum-Alloy Permanent Mold Castings
B666/B666M-20	Standard Practice for Identification Marking of Aluminum and Magnesium Products

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.