Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM B179-09

Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes

Automaticky preložený názov:

Štandardné špecifikácie pre hliníkové zliatiny v prút a Molten foriem pre odliatky z All Casting procesov

NORMA vydaná dňa 15.11.2009

Jazyk
Prevedenie	Online zabezpečené PDF - 81.60 € Tlačené - 81.60 €
Dostupnosť	SKLADOM
Cena	81.60 € bez DPH
81.60 €

Informácie o norme:

Označenie normy: ASTM B179-09
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.11.2009
Kód tovaru: NS-5620
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM B179-09 :

Keywords:

aluminum, ingot, molten metal, ICS Number Code 77.120.10 (Aluminium and aluminium alloys)

Doplňujúce informácie

1. Scope

1.1 This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The specific gravity of these alloys does not exceed 3.0 and they are designated as shown in Table 1.

Note 1

Throughout this specification the use of "ingot" in a general sense includes sow, T-bar, T-ingot, and pig.

1.2 Alloy designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designations are in accordance with Practice E 527.

Note 2

Supplementary data pertaining to the alloys covered by this specification when used in the form of castings are given in Specifications B 26/B 26M, B 85, B 108, B 618, and B 686.

1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1.

1.4 The values stated in inch-pound units are to be regarded as the standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

B686/B686M-25	Standard Specification for Aluminum Alloy Castings, High-Strength
B985-24	Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis
B955/B955M-25	Standard Specification for Aluminum-Alloy Centrifugal Castings
B969-10	Standard Specification for Aluminum-Alloy Castings Produced by the Squeeze Casting, Thixocast and Rheocast Semi-Solid Casting Processes
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34-11	Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E607-02	Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere
B26/B26M-25	Standard Specification for Aluminum-Alloy Sand Castings
B85/B85M-25	Standard Specification for Aluminum-Alloy Die Castings
E716-16(2021)e2	Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry (Includes all amendments and changes 9/7/2022).
E1251-25	Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
H35.1/H35.1(M)	American National Standard Alloy and Temper Designation Systems for Aluminum Available from Aluminum Association, Inc., 1525 Wilson Blvd., Suite 600, Arlington, VA 22209, http://www.aluminum.org.
Designations and Chemical Composition Limits for Aluminum Alloys in the Form of Castings and Ingot	(The Pink Sheets)
B618/B618M-25	Standard Specification for Aluminum-Alloy Investment Castings
B108/B108M-25	Standard Specification for Aluminum-Alloy Permanent Mold Castings
B666/B666M-20	Standard Practice for Identification Marking of Aluminum and Magnesium Products

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.