Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM B152/B152M-09
Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar
Automaticky preložený názov:
Štandardné špecifikácie pre medené plechy , pásy , dosky a vývalkov
NORMA vydaná dňa 1.10.2009
Informácie o norme:
Označenie normy: ASTM B152/B152M-09
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2009
Kód tovaru: NS-5498
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Anotácia textu normy ASTM B152/B152M-09 :
Keywords:
annealed, copper bars, copper plate, copper sheet, copper strip , hot-rolled, rolled, UNS No. C10100, UNS No. C10200, UNS No. C10300, UNS No. C10400, UNS No. C10500, UNS No. C10700, UNS No. C10800, UNS No. C10910, UNS No. C11000, UNS No. C11300, UNS No. C11400, UNS No. C11600, UNS No. C12000, UNS No. C12200, UNS No. C12300, UNS No. C14200, UNS No. C14420, UNS No. C14530, Bars (rolled copper), Copper alloy plate/sheet/strip/rolled bar--specifications, Plate (copper), Strip (copper)
Doplňujúce informácie
| 1. Scope | |||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers.
A Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin tellurium bearing) these types of copper are classified in Classification B224. B SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE Specification CA110 conforms to the requirements for Copper UNS No. C11000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper UNS Nos. C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements for Copper UNS No. C12200. C Unless specified in the contract or purchase order the supplier is permitted to provide ETP copper or TP copper. Note 1—Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the supplier to determine which copper would be best suited for the intended application. Note 2—This specification is not intended to establish requirements for material rolled to ounce-weight thicknesses. Such material is defined in Specification B370. Plates for locomotive fireboxes are defined in Specification B11. Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are defined in Specification B272. 1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of the listed coppers. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazards caveat only pertains to the test method portion, Section 13 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
|||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | |||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
