Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM B131-17

Standard Specification for Copper Alloy Bullet Jacket Cups

NORMA vydaná dňa 1.4.2017

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 74.70 € Tlačené - 74.70 €
Dostupnosť	SKLADOM
Cena	74.70 € bez DPH
74.70 €

Informácie o norme:

Označenie normy: ASTM B131-17
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2017
Kód tovaru: NS-680972
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Výrobky z mědi

Anotácia textu normy ASTM B131-17 :

Keywords:

bullet jackets, commercial bronze cups, UNS No. C22000,, ICS Number Code 77.150.30 (Copper products)

Doplňujúce informácie

Significance and Use

15.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value, or a calculated value, shall be rounded as indicated in accordance with the rounding method of Practice E29.

Property	Rounded Unit for Observed or Calculated Value

Chemical Composition	Nearest unit in the last right-hand significant digit used in expressing the limiting value

Grain size	Nearest multiple of 0.005 mm

1. Scope

1.1 This specification establishes the requirements for bullet jacket preform cups produced of Copper Alloy UNS No. C22000 for processing into bullet jackets of the following types and classes:

1.1.1 Type I—Caliber 0.30.

1.1.2 Type II—Caliber 0.45.

1.1.3 Type III—Caliber 0.50.

1.1.4 Type IV—As specified in the contract or order.

1.1.5 Class I—Not annealed.

1.1.6 Class II—Annealed.

1.2 Units—The values stated in inch-pound units are to be regarded as standard, except for grain size, which is given in SI units. The values in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.

1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

E478-08(2017)	Standard Test Methods for Chemical Analysis of Copper Alloys
B601-18a	Standard Classification for Temper Designations for Copper and Copper Alloys´Wrought and Cast (Includes all amendments and changes 10/24/2018).
E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E112-13(2021)	Standard Test Methods for Determining Average Grain Size
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E3-11(2017)	Standard Guide for Preparation of Metallographic Specimens
B846-19a	Standard Terminology for Copper and Copper Alloys (Includes all amendments and changes 8/8/2019).

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.