Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM B111/B111M-04

Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock

Automaticky preložený názov:

Štandardné špecifikácie pre medi a medených zliatin bezšvíkových rúr kondenzátora a dutinkou sklade

NORMA vydaná dňa 1.10.2004

Jazyk
Prevedenie	Online zabezpečené PDF - 81.60 € Tlačené - 81.60 €
Dostupnosť	SKLADOM
Cena	81.60 € bez DPH
81.60 €

Informácie o norme:

Označenie normy: ASTM B111/B111M-04
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2004
Kód tovaru: NS-5352
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM B111/B111M-04 :

Keywords:

condenser tube, copper, copper alloys, evaporator, ferrule stock, heat exchanger, seamless tube , UNS No. C10100, UNS No. C10200, UNS No. C10300, UNS No. C10800, UNS No. C12000, UNS No. C12200, UNS No. C14200, UNS No. C19200, UNS No. C23000, UNS No. C28000, UNS No. C44300, UNS No. C44400, UNS No. C44500, UNS No. C60800, UNS No. C61300, UNS No. C61400, UNS No. C68700, UNS No. C70400, UNS No. C70600, UNS No. C70620, UNS No. C71000, UNS No. C71500, UNS No. C71520, UNS No. C71640, UNS No. C

Doplňujúce informácie

1. Scope

1.1 This specification establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys up to 31/8 in. [80 mm] inclusive, in diameter, for use in surface condensers, evaporators, and heat exchangers. The following coppers and copper alloys are specified: (Warning-Mercury is a definite health hazard in use and disposal. (See 12.1.))

Designations listed in Classification B 224.

Copper orCopper AlloyUNS No.	PreviouslyUsed Designation	Description

C10100	OFE	Oxygen-free electronic
C10200	OF	Oxygen-free without residual deoxidants
C10300	. . .	Oxygen-free, extra low phosphorus
C10800	. . .	Oxygen-free, low phosphorus
C12000	DLP	Phosphorized, low residual phosphorus
C12200	DHP	Phosphorized, high residual phosphorus
C14200	DPA	Phosphorized, arsenical
C19200	. . .	Phosphorized, 1 % iron
C23000	. . .	Red Brass
C28000	. . .	Muntz Metal
C44300	. . .	Admiralty Metals, B, C, and D
C44400
C44500
C60800	. . .	Aluminum Bronze
C61300	. . .	. . .
C61400	. . .	Aluminum Bronze, D
C68700	. . .	Aluminum Brass, B
C70400	. . .	95-5 Copper-Nickel
C70600	. . .	90-10 Copper-Nickel
C70620	. . .	90-10 Copper-Nickel-Welding Grade
C71000	. . .	80-20 Copper-Nickel
C71500	. . .	70-30 Copper-Nickel
C71520	. . .	70-30 Copper-Nickel-Welding Grade
C71640	. . .	Copper-nickel-iron-manganese
C72200	. . .	. . .

1.2 UnitsValues stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 The following safety hazards caveat pertains only to the test methods portion, Section 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

E118-89(1996)	Standard Test Methods for Chemical Analysis of Copper-Chromium Alloys
E53-07	Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E76-88(1998)	Standard Test Methods for Chemical Analysis of Nickel-Copper Alloys (Withdrawn 2003)
E75-76(1996)	Standard Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E54-80(1996)	Standard Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E2575-19	Standard Test Method for Determination of Oxygen in Copper and Copper Alloys by Inert Gas Fusion
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E478-24	Standard Test Methods for Chemical Analysis of Copper Alloys
E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E112-25	Standard Test Methods for Determining Average Grain Size
B968/B968M-16(2022)	Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube
B153-22	Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing
B858-06(2024)	Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys
B846-24	Standard Terminology for Copper and Copper Alloys
B224-16(2022)	Standard Classification of Coppers
B170-24	Standard Specification for Oxygen-Free Electrolytic Copper—Refinery Shapes
E243-24	Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
B154-16(2022)	Standard Test Method for Mercurous Nitrate Test for Copper Alloys
E8/E8M-25	Standard Test Methods for Tension Testing of Metallic Materials

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.