Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Conducting Temperature Uniformity Surveys of Furnaces Used to Heat Treat Steel Products
NORMA vydaná dňa 15.4.2022
Označenie normy: ASTM A991/A991M-22
Dátum vydania normy: 15.4.2022
Kód tovaru: NS-1056595
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
furnace survey, temperature, uniformity, working zone,, ICS Number Code 25.200 (Heat treatment)
Significance and Use | ||||||||||
4.1?Furnaces for heat treatment of steel products are used in many industries, in many ways. Regardless of heat treat furnace type, or processing cycle, it may be necessary for users to know the temperature uniformity in the furnace and whether the material is processed in a zone within the furnace that is capable of meeting the applicable permissible temperature variation requirements. 4.2?The procedures in this test method may be used by those using, manufacturing, and providing calibration service for, heat treat furnaces used to process steel products. |
||||||||||
1. Scope | ||||||||||
1.1?This test method covers the procedures used to conduct a temperature uniformity survey on a furnace used to heat treat steel products. This method is used to determine the capability of the furnace to meet the permissible temperature variation specified in the applicable product specification, or as agreed to by the purchaser and supplier of heat treat services. Survey documentation requirements, and the procedure used to subsequently establish the furnace working zone, are defined in this test method. 1.2?This test method covers heat treat furnaces in any of the following categories: 1.2.1?Continuous or semi-continuous conveyance furnaces, 1.2.2?Batch furnaces, and 1.2.3?Salt or liquid baths and fluidized beds. 1.3?This test method only applies when specified in the product specification or the purchase order. 1.4?Controlling a heat treatment of steel products using thermocouples attached to the extremities of each load is an alternative to performing a furnace survey. The producer shall adhere to Annex A1. 1.5?By mutual agreement between the purchaser and the supplier of heat treat services, more stringent and/or additional requirements may be specified. The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier. 1.6?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||
2. Referenced Documents | ||||||||||
|
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.