Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM A989/A989M-15
Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
Automaticky preložený názov:
Štandardné špecifikácie pre Hot izostatickému lisované legovanej ocele príruby , armatúry, ventily, a dielov pre vysokej teplote službu
NORMA vydaná dňa 1.3.2015
Informácie o norme:
Označenie normy: ASTM A989/A989M-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2015
Kód tovaru: NS-585698
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM A989/A989M-15 :
Keywords:
alloy steel, chromium-alloy steel, chromium-molybdenum steel, gas-atomized powder, hot isostatically-pressed alloy steel parts, piping applications, pipe fittings, steel, pressure containing parts, steel flanges, steel valves, temperature service applications, elevated, temperature service applications, high,, ICS Number Code 49.025.10 (Steels)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||
|
1.1 This specification covers hot isostatically-pressed, powder metallurgy, alloy steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts made to specified dimensions or to dimensional standards, such as in ASME Specification B16.5. 1.2 Several grades of alloy steels are included in this specification. 1.3 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order. 1.4 This specification is expressed in both inch-pound units and in SI units. Unless the order specifies the applicable “M” specification designation (SI units), however, the material shall be furnished to inch-pound units. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.6 The following safety hazards caveat pertains
only to test methods portions, 8.1, 8.2, and 9.5 – 9.7 of this specification:
Standard Test Methods and Practices for
Chemical Analysis of Steel Products Standard Specification for Common
Requirements for Steel Flanges, Forged Fittings, Valves, and Parts
for Piping Applications Standard Test Method for Density of
Powder Metallurgy (PM) Materials Containing Less Than Two Percent
Porosity Standard Practice for Liquid Penetrant
Examination for General Industry SFA-5.5 Specification for Low-Alloy Steel Covered
Arc-Welding Electrodes Standard Practice for Macroetching Metals
and Alloys Standard Practice for Strain-Controlled
Fatigue Testing B16.5 Dimensional Standards for Steel Pipe
Flanges and Flanged Fittings Available from American Society of
Mechanical Engineers (ASME), ASME International Headquarters, Two
Park Ave., New York, NY 10016-5990, http://www.asme.org. Standard Practice for Magnetic Particle
Examination of Steel Forgings |
Odporúčame:
Aktualizácia zákonov
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
