Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM A932/A932M-01(2012)
Standard Test Method for Alternating-Current Magnetic Properties of Amorphous Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method with Sheet Specimens
Automaticky preložený názov:
Štandardná skúšobná metóda pre striedavý Magnetické vlastnosti amorfných materiálov v elektrárni frekvenciách využívajúcich wattmeter-ampérmetra voltmeter metóda s listov vzoriek
NORMA vydaná dňa 1.5.2012
Informácie o norme:
Označenie normy: ASTM A932/A932M-01(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2012
Kód tovaru: NS-4873
Počet strán: 13
Približná hmotnosť: 39 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM A932/A932M-01(2012) :
Keywords:
ac, ammeter, amorphous, anneal, core loss, exciting power, form factor, magnetic, peak, permeability, sheet, specific, voltmeter, wattmeter, waveform, yoke, ICS Number Code 17.220.20 (Measurement of electrical and magnetic quantities)
Doplňujúce informácie
| Significance and Use | ||||||||||||
|
4.1 This test method provides a satisfactory means of determining various ac magnetic properties of amorphous magnetic materials. It was developed to supplement the testing of toroidal and Epstein specimens. For testing toroidal specimens of amorphous materials, refer to Test Method A912/A912M. 4.2 The procedures described herein are suitable for use by manufacturers and users of amorphous magnetic materials for materials specification acceptance and manufacturing control. 1.1 This test method covers tests
for various magnetic properties of flat-cast amorphous magnetic
materials at power frequencies (50 and 60 Hz) using sheet-type
specimens in a yoke-type test fixture. It provides for testing
using either single- or multiple-layer specimens.
1.2 This test method provides a test
for specific core loss, specific exciting power and ac peak
permeability at moderate and high flux densities, but is restricted
to very soft magnetic materials with dc coercivities of 0.07 Oe
[5.57 A/m] or less.
1.3 The test method also provides procedures for calculating ac peak permeability from measured peak values of total exciting currents at magnetic field strengths up to about 2 Oe [159 A/m]. 1.4 Explanation of symbols and abbreviated definitions appear in the text of this test method. The official symbols and definitions are listed in Terminology A340. 1.5 This test method shall be used in conjunction with Practice A34/A34M. 1.6 The values stated in either customary (cgs-emu and inch-pound) or SI units are to be regarded separately as standard. Within this standard, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
