ASTM E1955-04(2009)..
ASTM E2373/E2373M-14..
ASTM E2700-14
ASTM E2818-11
ASTM E390-11
ASTM F1269-13
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM A928/A928M-14
Standard Specification for Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric Fusion Welded with Addition of Filler Metal
Automaticky preložený názov:
Štandardné špecifikácie pre feritické / austenitické (Duplex) rúrky z nerezovej ocele Elektrický Fusion zvárané s prídavkom prídavného kovu
NORMA vydaná dňa 1.10.2014
Informácie o norme:
Označenie normy: ASTM A928/A928M-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2014
Kód tovaru: NS-4858
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM A928/A928M-14 :
Keywords:
arc welded steel pipe, corrosive service, duplex (austenitic-ferritic) stainless steel, fusion welded steel pipe, steel pipe, welded steel pipe, ICS Number Code 25.160.40 (Welding joints and welds)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||
|
1.1 This specification covers electric-fusion-welded steel pipe suitable for corrosive service. Note 1: The dimensionless designator NPS (nominal pipe size)
has been substituted in this specification for traditional terms
such as nominal diameter, size, and nominal size.
1.2 This specification covers grades of ferritic/austenitic steel as indicated in Table 1. The selection of the proper alloy and requirements for heat treatment shall be at the discretion of the purchaser, dependent on the service conditions to be encountered. 1.3 Five classes of pipe are covered as
follows:
1.3.1 Class 1—Pipe shall be double welded by processes using filler metal in all passes and shall be radiographed completely. 1.3.2 Class 2—Pipe shall be double welded by processes using filler metal in all passes. No radiograph is required. 1.3.3 Class 3—Pipe shall be single welded by processes using filler metal in all passes and shall be radiographed completely. 1.3.4 Class 4—Same as Class 3, except that the weld pass exposed to the inside pipe surface is permitted to be made without the addition of filler metal (see 6.2.2.1 and 6.2.2.2). 1.3.5 Class 5—Pipe shall be double welded by processes using filler metal in all passes and shall be spot radiographed. 1.4 Supplementary requirements covering provisions ranging from additional testing to formalized procedures for manufacturing practice are provided. Supplementary Requirements S1 through S4 are included as options to be specified in the purchase order when desired. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the M designation of the specification is specified in the order. |
||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||
|
Podobné normy:
Historická
1.6.2009
Historická
1.6.2014
Historická
1.10.2014
Historická
1.5.2011
Historická
1.8.2011
Historická
1.1.2013
Odporúčame:
Aktualizácia zákonov
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
