Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM A805/A805M-09(2021)
Standard Specification for Steel, Flat Wire, Carbon, Cold-Rolled
NORMA vydaná dňa 1.9.2021
Informácie o norme:
Označenie normy: ASTM A805/A805M-09(2021)
Dátum vydania normy: 1.9.2021
Kód tovaru: NS-1036729
Počet strán: 13
Približná hmotnosť: 39 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM A805/A805M-09(2021) :
This specification covers carbon steel flat wire in coils or cut lengths. The steel materials shall be produced from rimmed, capped, semi-killed, hot-rolled or cold-rolled steel. The steel specimens shall undergo cast or heat analysis and product analysis and shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, and copper. The desired edge shall be classified as follows: prepared edge of a specified contour produced when a very accurate width is required or when the finish of the edge suitable for electroplating is required, or both (Number 1 Edge); not applicable to flat wire products ( Number 2 Edge); approximately square edge produced by slitting (Number 3 Edge); rounded edge produced either by edge rolling or resulting from flat rolling of a round section (Number 4 Edge); square edge produced from slit-edge material on which the burr is eliminated by rolling or filling (Number 5 Edge); and square edge produced by edge rolling when the width tolerance and edge condition are not as exacting as for No. 1 Edge (Number 6 Edge). The dimensional tolerances shall conform to the required values of thickness, width and length. The steel materials shall conform to the required values of temper, Rockwell hardness and tensile strength.
Keywords:
ICS Number Code 77.140.65 (Steel wire, wir ropes and link chains)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||
|
1.1?This specification covers carbon steel flat wire in coils or cut lengths. Flat wire is classified as a cold-rolled section, rectangular in shape, 0.500 in. [12.7 mm] or less in width and under 0.250 in. [6.35 mm] in thickness. 1.2?Low-carbon steel flat wire is produced from steel compositions with a maximum carbon content of 0.25 % by cast or heat analysis. 1.3?Carbon spring steel flat wire is produced to a carbon range in which the specified or required maximum is over 0.25 % by cast or heat analysis. 1.3.1?Two types of carbon spring steel flat wire are produced: 1.3.1.1?Untempered cold-rolled carbon spring steel flat wire, produced to several desirable combinations of properties and 1.3.1.2?Hardened and tempered carbon spring steel wire. 1.4?Definite application flat wire is a product developed for a specific application and may be specified only by size and descriptive name. 1.5?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||
|
Odporúčame:
EviZak - všetky zákony vrátane ich evidencie na jednom mieste
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
