Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM A74-13a

Standard Specification for Cast Iron Soil Pipe and Fittings (Includes all amendments And changes 9/30/2015).

Automaticky preložený názov:

Štandard Specification pre liatinu kanalizáciu a ich príslušenstvo

NORMA vydaná dňa 1.6.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 124.10 € Tlačené - 124.10 €
Dostupnosť	SKLADOM
Cena	124.10 € bez DPH
124.10 €

Informácie o norme:

Označenie normy: ASTM A74-13a
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2013
Kód tovaru: NS-3957
Počet strán: 45
Približná hmotnosť: 135 g (0.30 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM A74-13a :

Keywords:

cast iron, fitting, hub and spigot pipe, pipe, soil pipe, ICS Number Code 23.040.40 (Metal fittings)

Doplňujúce informácie

1. Scope

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the applicable requirements given in this specification.

1.2.1 Pipe:

Tables

Extra heavy, 2¹/₂ ft (0.75 m), 3¹/₂ ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths

1, 2

Service, 2¹/₂ ft (0.75 m), 3¹/₂ ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m)

1, 2

Outside dimensions (for detailing)

X1.1

1.2.2 Fittings:

Tables

¹/₄ bends; long ¹/₄ bends

3, 4

¹/₄ bends, long low-hub

¹/₄ bends, low heel; high heel

6, 7

¹/₄ bends, short sweep; long sweep

¹/₄ bends, reducing long sweep

¹/₅ bends

¹/₆ bends

¹/₈ bends; long ¹/₈ bends

¹/₁₆ bends

Y branches

12, 13

Y branches, combination ¹/₈ bends, single

Y branches, combination ¹/₈ bends, double

Sanitary T branches, single

Sanitary T branches, double

Sanitary T branches, cleanout

Tapped sanitary T branches, single

Tapped sanitary T branches, double

T branches, single and double

Tapped T branches, single

Tapped T branches, double

T branches, cleanout

-45° offset fitting

Double hubs

Long double hubs

Reducers

Increasers

24, 25

P traps

26, 27

Deep seal P traps

Running traps

Screw plugs (brass)

Blind plugs

Iron-body ferrules

Side inlets

Fig. 3

Closet bends

Tapping bosses

Reducing ¹/₄ bend SV

Combination Y and ¹/₈ bend

‘H’ branch fitting

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

2. Referenced Documents

D3960-05(2018)	Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
E8-04	Standard Test Methods for Tension Testing of Metallic Materials
MIL-STD-129	Marking for Shipment and Storage
A48/A48M-22	Standard Specification for Gray Iron Castings
A644-17	Standard Terminology Relating to Iron Castings
D1248-16	Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
E1645-21	Standard Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis
B1.20	Pipe Threads
E2349-19	Standard Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)

Doporučujeme: