Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM A74-05

Standard Specification for Cast Iron Soil Pipe and Fittings

Automaticky preložený názov:

Štandardné špecifikácie pre Cast Iron pôdy potrubia a armatúr

NORMA vydaná dňa 1.6.2005

Jazyk
Prevedenie	Online zabezpečené PDF - 116.10 € Tlačené - 116.10 €
Dostupnosť	SKLADOM
Cena	116.10 € bez DPH
116.10 €

Informácie o norme:

Označenie normy: ASTM A74-05
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2005
Kód tovaru: NS-3951
Počet strán: 44
Približná hmotnosť: 132 g (0.29 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM A74-05 :

Keywords:

cast iron, fitting, hub and spigot pipe, pipe, soil pipe, ICS Number Code 23.040.40 (Metal fittings)

Doplňujúce informácie

1. Scope

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the applicable requirements given in this specification.

1.2.1 Pipe

	Tables
Extra heavy, 21/ 2 ft (0.75 m), 31/2ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths	1, 2
Service, 21/2 ft (0.75 m), 31/2ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m)	1, 2
Outside dimensions (for detailing)	X1.1

1.2.2 Fittings

	Tables
1/4 bends; long 1/4 bends	3, 4
1/4 bends, long low-hub	5
1/4 bends, low heel; high heel	6, 7
1/4 bends, short sweep; long sweep	8
1/4 bends, reducing long sweep	9
1/5 bends	10
1/6 bends	10
1/8 bends; long 1/8 bends	11
1/16 bends	11
Y branches	12, 13
Y branches, combination 1/8 bends, single	14
Y branches, combination 1/8 bends, double	14
Sanitary T branches, single	15
Sanitary T branches, double	15
Sanitary T branches, cleanout	16
Tapped sanitary T branches, single	17
Tapped sanitary T branches, double	17
T branches, single and double	18
Tapped T branches, single	19
Tapped T branches, double	19
T branches, cleanout	20
-45 offset fitting	21
Double hubs	22
Long double hubs	22
Reducers	23
Increasers	24, 25
P traps	26, 27
Deep seal P traps	28
Running traps	29
Screw plugs (brass)	30
Blind plugs	31
Iron-body ferrules	32
Side inlets	Fig. 3
Closet bends	33
Tapping bosses	34
Reducing 1/4 bend SV	35
Combination Y and 1/8 bend	36
H branch fitting	37

1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. Metric conversions in Tables 1 and 2 are to two decimal places; all other metric conversions are rounded to the nearest whole number.

2. Referenced Documents

D3960-05(2018)	Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
E8-04	Standard Test Methods for Tension Testing of Metallic Materials
MIL-STD-129	Marking for Shipment and Storage
A48/A48M-22	Standard Specification for Gray Iron Castings
A644-17	Standard Terminology Relating to Iron Castings
D1248-16	Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
E1645-21	Standard Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis
B1.20	Pipe Threads
E2349-19	Standard Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.