Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Precipitation–Strengthened Low-Carbon Nickel-Copper-Chromium-Molybdenum-Columbium Alloy Structural Steel Plates
Automaticky preložený názov:
Štandardné špecifikácie pre Precipitation & ndash; Posilnenie Low-Carbon nikel-meď-chróm-molybdénovej-niób Alloy konštrukčná oceľ dosky
NORMA vydaná dňa 15.5.2013
Označenie normy: ASTM A710/A710M-02(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.5.2013
Kód tovaru: NS-3833
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
alloy, carbon, chromium, columbium, copper, general applications, low carbon, manganese, molybdenum, nickel, plates, precipitation heat treatment, precipitation strengthening, steel, structural steel, ICS Number Code 77.080.20 (Steels)
1. Scope | ||||||||||||||
1.1 This specification covers low-carbon precipitation—strengthened nickel - copper - chromium - molybdenum - columbium alloy steel plates for general applications. The alloys in this specification are strengthened by precipitation in various temperature ranges. Precipitation strengthening can occur upon air cooling after hot rolling, during normalizing, and by another heat treatment. These grades are not intended for use in applications above 900°F [540°C]. 1.2 Two grades, each with three
classes, are provided as follows:
1.3 Grade A provides minimum yield strength levels ranging from 50 to 85 ksi [345 to 585 MPa], depending on thickness and condition. 1.4 Grade A, Class 1, plates are limited to a maximum thickness of 3/4 in. [20 mm]. The maximum thickness of Grade A, Classes 2 and 3, is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness to 8 in. [200 mm]. 1.5 Mandatory notch toughness requirements are specified for Grade A, Class 1. 1.6 Grade B provides minimum yield strength levels ranging from 70 to 75 ksi [480 to 515 MPa], depending on thickness and condition. 1.7 Grade B plates are limited to a maximum thickness of 2 in. [50 mm]. 1.8 Mandatory notch toughness requirements are specified for the three classes of Grade B. 1.9 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability. 1.10 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. |
||||||||||||||
2. Referenced Documents | ||||||||||||||
|
Historická
15.11.2012
Historická
1.6.2014
Historická
1.5.2010
Historická
1.5.2014
Historická
1.5.2014
Historická
1.1.2014
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-09-08 (Počet položiek: 2 346 102)
© Copyright 2024 NORMSERVIS s.r.o.