Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM A684/A684M-86(1998)

Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled

Automaticky preložený názov:

Štandardné špecifikácie pre Steel Strip, High - Carbon , valcované za studena

NORMA vydaná dňa 10.9.1998

Jazyk
Prevedenie	Online zabezpečené PDF - 65.70 € Tlačené - 65.70 €
Dostupnosť	SKLADOM
Cena	65.70 € bez DPH
65.70 €

Informácie o norme:

Označenie normy: ASTM A684/A684M-86(1998)
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.9.1998
Kód tovaru: NS-3683
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM A684/A684M-86(1998) :

Keywords:

Carbon steel plate/sheet/strip, Intermediate hardness carbon spring steel, Spheroidized carbon spring steel, Steel strip-carbon steel, strip-high-carbon steel, cold-rolled, spec

Doplňujúce informácie

1. Scope

1.1 This specification covers cold-rolled, high-carbon strip. It is furnished in the following types as specified:

1.1.1 Soft spheroidized annealed high-carbon steel is intended for applications requiring maximum cold forming. It is normally produced to give the lowest maximum Rockwell hardness for each grade.

1.1.2 Soft annealed high-carbon steel is intended for applications requiring moderate cold forming. It is produced to a maximum Rockwell hardness.

1.1.3 Intermediate hardness high-carbon steel is intended for applications where cold forming is slight or a stiff, springy product is needed, or both. It is produced to specified Rockwell hardness ranges, the maximum being higher than obtained for the annealed type.

1.1.4 Full hard high-carbon steel is intended for flat applications. It is produced to minimum Rockwell hardness requirements, which vary with grade, microstructure and gage. Full hard can be produced with either a pearlitic or spheroidized microstructure or a mixture of both. The minimum hardness should be established between the consumer and the producer.

1.2 This specification is applicable for orders in either inch-pound units (as A684) or SI units (A684M).

2. Referenced Documents

A1073/A1073M-21	Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
A941-23	Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
MIL-STD-129	Marking for Shipping and Storage

A109/A109M-24	Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products
A700-14(2019)	Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment
Fed. Std. No. 183	Continuous Identification Marking of Iron and Steel Products
Fed. Std. No. 123	Marking for Shipments (Civil Agencies) Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E3-11(2017)	Standard Guide for Preparation of Metallographic Specimens
A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products
A568/A568M-19a	Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for (Includes all amendments and changes 11/22/2019).

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.