Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM A635/A635M-15
Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for
Automaticky preložený názov:
Štandardné špecifikácie pre oceľ, plechy a pásy , ťažkého Hrúbka cievky , valcované za tepla , zliatina , Carbon , štrukturálne , vysokopevnostné nízkolegovanej , a High - Low - Alloy pevnosť sa zlepšeným tvárniteľnosti , Všeobecné požiadavky na
NORMA vydaná dňa 1.11.2015
Informácie o norme:
Označenie normy: ASTM A635/A635M-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2015
Kód tovaru: NS-620462
Počet strán: 15
Približná hmotnosť: 45 g (0.10 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM A635/A635M-15 :
Keywords:
carbon, commercial, drawing, heavy thickness coils, high-strength low-alloy, high-strength low-alloy with improved formability, sheet steel, strip steel,, ICS Number Code 77.140.50 (Flat steel products and semi-products)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||||
|
1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils. 1.2 It applies to Specifications A414/A414M, A424/A424M, and A1018/A1018M. 1.3 This material is available only in coils described as follows:
Note 1: The changes in width limits with the publication of
A635/A635M – 06a result in a
change in tensile testing direction for material from 0.180 in.
[4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in.
[1200 mm] wide, as that material is now covered by Specification
A568/A568M – 06a. The
purchaser is advised to discuss this change with the
supplier.
1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification is used. Note 2: The term weight is used when inch-pound units are
the standard. However, under SI, the preferred term is mass.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. |
||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||
|
||||||||||||||||||||||||||
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
