Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM A635/A635M-13 1.10.2013 náhľad

Doplňujúce informácie

ASTM A635/A635M-13

Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for

Automaticky preložený názov:

Štandardné špecifikácie pre oceľ, plechy a pásy , Heavy hrúbke cievky , valcované za tepla , zliatina , Carbon , štrukturálne , vysokopevnostného Low - Alloy , a High - pevnosť Low - Alloy s vylepšenou tvárniteľnosti , Všeobecné požiadavky na

NORMA vydaná dňa 1.10.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 87.60 € Tlačené - 87.60 €
Dostupnosť	SKLADOM
Cena	87.60 € bez DPH
87.60 €

Informácie o norme:

Označenie normy: ASTM A635/A635M-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2013
Kód tovaru: NS-3467
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM A635/A635M-13 :

Keywords:

carbon , commercial, drawing, heavy thickness coils, high-strength low-alloy, high-strength low-alloy with improved formability, sheet steel, strip steel, ICS Number Code 77.140.50 (Flat steel products and semi-products)

Doplňujúce informácie

1. Scope

1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.

1.2 It applies to Specifications A414/A414M, A424/A424M, and A1018/A1018M.

1.3 This material is available only in coils described as follows:

Size Limits, Coils Only

Product

Width, in. [mm]

Thickness, in. [mm]

Strip

over 8 to 12, incl
[over 200 through 300]

0.230 to 1.000, incl
[from 6.0 through 25]

Sheet

All Widths^A
All Widths

0.230 to 1.000, incl
[from 6.0 through 25]

1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.

1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.

2. Referenced Documents

A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products
A941-23	Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A1018/A1018M-23a	Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength (Includes all amendments and changes 12/8/2023).
A700-14(2019)	Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A568/A568M-19a	Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for (Includes all amendments and changes 11/22/2019).
MIL-STD-129	Marking for Shipment and Storage
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E11-22	Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
A1073/A1073M-21	Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
A424/A424M-18	Standard Specification for Steel, Sheet, for Porcelain Enameling
A414/A414M-23	Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels
A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.