Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM A635/A635M-05

Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for

Automaticky preložený názov:

Štandardné špecifikácie pre oceľ, plechy a pásy , Heavy hrúbke cievky , valcované za tepla , uhlík , štrukturálne , vysokopevnostné Low - Alloy , a High - pevnosť Low - Alloy s vylepšenou tvárniteľnosti , Všeobecné požiadavky na

NORMA vydaná dňa 1.5.2005

Jazyk
Prevedenie	Online zabezpečené PDF - 76.80 €
Dostupnosť	SKLADOM
Cena	76.80 € bez DPH
76.80 €

Informácie o norme:

Označenie normy: ASTM A635/A635M-05
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2005
Kód tovaru: NS-3459
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM A635/A635M-05 :

Keywords:

carbon commercial, drawing, heavy thickness coils, high-strength low-alloy, high-strength low-alloy with improved formability, sheet steel, strip steel

Doplňujúce informácie

1. Scope

1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.

1.2 It applies to Specification A 1018/A 1018M.

1.3 This material is available only in coils described as follows:

	Size Limits, Coils Only
Product	Width, in. [mm]	Thickness, in. [mm]

Strip	over 8 to 12, incl[over 200 through 300]	0.230 to 1.000, incl [from 6.0 through 25]
Sheet	over 12 to 48, incl [over 300 through 1200]	0.230 to 1.000, incl[from 6.0 through 25]
Sheet	over 48[over 1200]	0.180 to 1.000, incl[from 4.5 though 25]

1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.

1.5 lists permissible variations in dimensions and mass (see Note 0) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. The term weight is used when inch-pound units are the standard. However, under SI, the preferred term is mass.

1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.

1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.

2. Referenced Documents

A751-25	Standard Test Methods and Practices for Chemical Analysis of Steel Products
A941-26a	Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys (Includes all amendments and changes 4/15/2026).
A1018/A1018M-25	Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High-Strength
A700-14(2019)	Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A568/A568M-25a	Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for (Includes all amendments and changes 12/5/2025).
MIL-STD-129	Marking for Shipment and Storage
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E11-24	Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
A1073/A1073M-21	Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
A424/A424M-25	Standard Specification for Steel, Sheet, for Porcelain Enameling
A414/A414M-25a	Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels (Includes all amendments and changes 12/5/2025).
A370-26	Standard Test Methods and Definitions for Mechanical Testing of Steel Products

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.