Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM A600-92a(2010) 1.10.2010 náhľad

Doplňujúce informácie

ASTM A600-92a(2010)

Standard Specification for Tool Steel High Speed (Includes all amendments And changes 6/9/2016).

Automaticky preložený názov:

Štandardné špecifikácie pre nástrojovej ocele High Speed

NORMA vydaná dňa 1.10.2010

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 77.70 € Tlačené - 77.70 €
Dostupnosť	SKLADOM
Cena	77.70 € bez DPH
77.70 €

Informácie o norme:

Označenie normy: ASTM A600-92a(2010)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2010
Kód tovaru: NS-3316
Počet strán: 14
Približná hmotnosť: 42 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Tepelně zpracovatelné oceli

Anotácia textu normy ASTM A600-92a(2010) :

Keywords:

high speed, tool steel, High speed tool steel, Molybdenum--specifications, Molybdenum high-speed tool steel, Steel forgings--specifications, Steel forgings (tool steel), Steel plate--specifications, Steel sheet--specifications, Steel strip, Tool steel--specifications, Tungsten high-speed tool steel, ICS Number Code 77.140.10 (Heat-treatable steels)

Doplňujúce informácie

1. Scope

1.1 This specification covers tungsten-type and molybdenum-type high-speed steels available as annealed, hot-rolled bars, forgings, plate, sheet, or strip, and annealed, cold-finished bars or forgings used primarily in the fabrication of tools.

1.2 Seven types of tungsten high-speed tool steels designated T1, T2, etc., seventeen types of molybdenum high-speed tool steels designated M1, M2, etc., and two intermediate high speed steels designated as M50 and M52 are covered. Selection will depend upon design, service conditions, and mechanical properties.

1.3 The term “high-speed steel” is described and its minimum requirements are covered in the Annex.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

2. Referenced Documents

E3-11(2017)	Standard Guide for Preparation of Metallographic Specimens
E45-18a(2023)	Standard Test Methods for Determining the Inclusion Content of Steel (Includes all amendments and changes 11/6/2023).
Fed. Std. No. 183
A561-08(2020)	Standard Practice for Macroetch Testing of Tool Steel Bars
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
E30-89	Test Methods for Chemical Analysis of Steel, Cast Iron, Open-Hearth Iron, and Wrought Iron (Withdrawn 1995)
E59-93	Practice for Sampling Steel and Iron for Determination of Chemical Composition (Withdrawn 1996)
MIL-STD-163	Steel Mill Products, Preparation for Shipment and Storage Available from DLA Document Services, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, http://quicksearch.dla.mil.
A388/A388M-23	Standard Practice for Ultrasonic Examination of Steel Forgings
A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products
A700-14(2019)	Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment