Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM A600-92a(1999)

Standard Specification for Tool Steel High Speed (Includes all amendments And changes 8/16/2017).

Automaticky preložený názov:

Štandardné špecifikácie pre nástrojovej ocele High Speed

NORMA vydaná dňa 10.9.1999

Jazyk
Prevedenie	Online zabezpečené PDF - 81.90 € Tlačené - 81.90 €
Dostupnosť	SKLADOM
Cena	81.90 € bez DPH
81.90 €

Informácie o norme:

Označenie normy: ASTM A600-92a(1999)
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.9.1999
Kód tovaru: NS-3314
Počet strán: 12
Približná hmotnosť: 36 g (0.08 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM A600-92a(1999) :

Keywords:

Molybdenum high-speed tool steel, Steel bars-general, Steel forgings, Steel plate-general, Steel sheet-general, Steel strip, Tungsten high-speed tool steel, tool steel-tungsten-/molybdenum-type, high-speed (for fabrication of, tools), spec, ICS Number Code 77.140.10 (Heat-treatable steels)

Doplňujúce informácie

1. Scope

1.1 This specification covers tungsten-type and molybdenum-type high-speed steels available as annealed, hot-rolled bars, forgings, plate, sheet, or strip, and annealed, cold-finished bars or forgings used primarily in the fabrication of tools.

1.2 Seven types of tungsten high-speed tool steels designated T1, T2, etc., seventeen types of molybdenum high-speed tool steels designated M1, M2, etc., and two intermediate high speed steels designated as M50 and M52 are covered. Selection will depend upon design, service conditions, and mechanical properties.

1.3 The term "high-speed steel" is described and its minimum requirements are covered in the Annex.

1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.

2. Referenced Documents

E3-11(2017)	Standard Guide for Preparation of Metallographic Specimens
E45-18a(2023)	Standard Test Methods for Determining the Inclusion Content of Steel (Includes all amendments and changes 11/6/2023).
Fed. Std. No. 183
A561-08(2020)	Standard Practice for Macroetch Testing of Tool Steel Bars
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
E30-89	Test Methods for Chemical Analysis of Steel, Cast Iron, Open-Hearth Iron, and Wrought Iron (Withdrawn 1995)
E59-93	Practice for Sampling Steel and Iron for Determination of Chemical Composition (Withdrawn 1996)
MIL-STD-163	Steel Mill Products, Preparation for Shipment and Storage Available from DLA Document Services, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, http://quicksearch.dla.mil.
A388/A388M-23	Standard Practice for Ultrasonic Examination of Steel Forgings
A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products
A700-14(2019)	Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.