Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet
Automaticky preložený názov:
Štandardné špecifikácie pre výrobky z bieleho plechu, elektrolytické Tin-Coated, valcované za studena plech
NORMA vydaná dňa 1.3.2012
Označenie normy: ASTM A599/A599M-07(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2012
Kód tovaru: NS-3282
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
ICS Number Code 77.140.50 (Flat steel products and semi-products)
1. Scope | ||
1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Designation No. |
Nominal Tin Coating |
Minimum Average Coating |
5 (0.6/0.6) |
0.025/0.025 (0.6/0.6) |
0.02/0.02 (0.5/0.5) |
10 (1.1/1.1) |
0.05/0.05 (1.1/1.1) |
0.04/0.04 (0.9/0.9) |
15 (1.7/1.7) |
0.075/0.075 (1.7/1.7) |
0.06/0.06 (1.4/1.4) |
20 (2.2/2.2) |
0.10/0.10 (2.2/2.2) |
0.08/0.08 (1.8/1.8) |
25 (2.8/2.8) |
0.125/0.125 (2.8/2.8) |
0.11/0.11 (2.5/2.5) |
50 (5.6/5.6) |
0.25/0.25 (5.6/5.6) |
0.23/0.23 (5.2/5.2) |
75 (8.4/8.4) |
0.375/0.375 (8.4/8.4) |
0.35/0.35 (7.8/7.8) |
100 (11.2/11.2) |
0.50/0.50 (11.2/11.2) |
0.45/0.45 (10.1/10.1) |
1.2 Limitations—This specification is applicable to orders in either inch-pound units (as A599), which is supplied in thicknesses from 0.015 in. to 0.036 in., or SI units [as A599M], which is supplied in thicknesses from 0.381 mm to 0.914 mm. For thicknesses lighter than 0.015 in. [0.381 mm], refer to A624/A624M [A624M].
1.3 Unless the order shows the “M” designation [SI units], the product shall be furnished to inch-pound units. The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable (Includes all amendments and changes 12/29/2023). |
|
Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment |
|
Standard Specification for Tin Mill Products, Electrolytic Tin Plate, Single Reduced |
|
Standard Specification for Tin Mill Products, General Requirements [Metric] |
|
Standard Specification for Tin Mill Products, General Requirements |
|
Standard Test Methods for Determination of Tin Coating Weights for Electrolytic Tin Plate (Includes all amendments and changes 3/6/2024). |
|
Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for (Includes all amendments and changes 11/22/2019). |
Historická
1.5.2014
Historická
1.5.2014
Historická
1.11.2009
Historická
1.4.2013
Historická
1.11.2010
Historická
1.5.2014
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-23 (Počet položiek: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.