Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM A554-15a

Standard Specification for Welded Stainless Steel Mechanical Tubing (Includes all amendments And changes 3/8/2016).

Automaticky preložený názov:

Štandardné podmienky pre zvárané oceľové nerezovej ocele Mechanické Tubing

NORMA vydaná dňa 1.9.2015

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 72.10 € Tlačené - 72.10 €
Dostupnosť	SKLADOM
Cena	72.10 € bez DPH
72.10 €

Informácie o norme:

Označenie normy: ASTM A554-15a
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.9.2015
Kód tovaru: NS-614677
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Železné a ocelové trubky
Kovové fitinky

Anotácia textu normy ASTM A554-15a :

Keywords:

austenitic stainless steel, austenitic-ferritic duplex stainless steel, exhaust tubing, ferritic stainless steel tubing, mechanical tubing, ornamental tubing, stainless steel tube, steel tube, structural tubing, welded steel tube ,, ICS Number Code 23.040.10 (Iron and steel pipes), 23.040.40 (Metal fittings)

Doplňujúce informácie

1. Scope

1.1 This specification covers welded austenitic, ferritic, and austenitic-ferritic duplex stainless steel mechanical tubing intended for use in ornamental, structural, exhaust, and other applications where appearance, mechanical properties, or corrosion resistance is needed. The grades covered are listed in Table 1.

1.2 This specification covers as-welded or cold-reduced mechanical tubing in sizes to 16 in. (406.4 mm) outside dimension, and in wall thicknesses 0.020 in. (0.51 mm) and over.

1.3 Tubes shall be furnished in one of the following shapes as specified by the purchaser: round, square, rectangular, or special.

1.4 Supplementary requirements of an optional nature are provided and when desired shall be so stated in the order.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

2. Referenced Documents

SAE J 1086	Numbering Metals and Alloys
MIL-STD-163	Steel Mill Products Preparation for Shipment and Storage
Fed. Std. No. 123	Marking for Shipments (Civil Agencies)
MIL-STD-129	Marking for Shipment and Storage Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 191115094, Attn: NPODS.
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
A941-23	Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A790/A790M-23	Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe
A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products
A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products