Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)
Automaticky preložený názov:
Štandardné špecifikácie pre vysokopevnostnej ocele , skrutky tried 10,9 a 10.9.3 , pre konštrukčné ocele Kĺby ( metrické )
NORMA vydaná dňa 1.8.2014
Označenie normy: ASTM A490M-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.8.2014
Kód tovaru: NS-2779
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
alloy steel, bolts, metric, SI, steel, structural, weathering steel,, ICS Number Code 21.060.10 (Bolts, screws, studs)
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1.1 This specification covers two types of quenched and tempered alloy steel, metric heavy hex structural bolts having a tensile strength of 1040 to 1210 MPa. 1.2 These bolts are intended for use in structural connections comparable to those covered under the requirements of the Specification for Structural Joints Using ASTM A325 and A490 bolts, approved by the Research Council on Structural Connections; endorsed by the American Institute of Steel Construction and by the Industrial Fastener Institute.1.3 The bolts are furnished in nominal bolt diameters M12 to M36, inclusive. They are designated by type denoting chemical composition as follows:
1.4 This specification is applicable to metric heavy hex structural bolts and alternate designs as established by the Research Council in its publication, Specification for Structural Joints Using ASTM and bolts. 1.5 For inch-pound bolts, see Specification A490. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 The following safety hazards caveat pertains only to the Test Methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
|
|
Standard Terminology for F16 Mechanical Fasteners
|
|
Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)
|
|
Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
|
B1.13M
|
Metric Screw Threads
|
B18.2.3.7M
|
Metric Heavy Hex Structural Bolts
|
B18.24
|
Part Identifying Number (PIN) Code System Standard for B18 Fastener Products
|
7412
|
Hexagon Bolts for High Strength Structural Bolting With Large Width Across Flats (Short Thread Length)-Product Grade C-Property Classes 8.8 and 10.9
|
IFI 144
|
Test Evaluation Procedures for Coating Qualification Intended for Use on High-Strength Structural Bolts
|
|
Standard Specification for Corrosion Protective Fastener Coatings with Zinc Rich Base Coat and Aluminum Organic/Inorganic Type
|
|
Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength (Withdrawn 2016)
|
|
Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength
|
|
Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)
|
|
Standard Specification for Carbon and Alloy Steel Nuts [Metric]
|
|
Standard Test Methods and Practices for Chemical Analysis of Steel Products
|
|
Standard Practice for Commercial Packaging
|
|
Standard Test Method for Microindentation Hardness of Materials
|
|
Standard Practice for Magnetic Particle Testing
|
|
Standard Specification for Hardened Steel Washers [Metric] (Withdrawn 2016)
|
|
Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Withdrawn 2012)
|
|
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric) (Withdrawn 2015)
|
|
Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series (Includes all amendments and changes 9/12/2023).
|
|
Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use With Structural Fasteners (Metric) (Withdrawn 2016)
|
|
Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners [Metric] (Withdrawn 2011)
|
|
Standard Guide for Magnetic Particle Testing |
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.