Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM A453/A453M-08
Standard Specification for High-Temperature Bolting Materials, with Expansion Coefficients Comparable to Austenitic Stainless Steels
Automaticky preložený názov:
Štandardné špecifikácie pre vysokoteplotné vybiehanie materiálov , s koeficientmi rozťažnosti Porovnateľné s austenitickej nehrdzavejúcej ocele
NORMA vydaná dňa 1.10.2008
Informácie o norme:
Označenie normy: ASTM A453/A453M-08
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2008
Kód tovaru: NS-2542
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Anotácia textu normy ASTM A453/A453M-08 :
Keywords:
bolts-steel, fasteners-steel, marking, nuts-steel, precipitation hardening steels, pressure vessel service, revision letter, steel bars-alloy, steel bolting material, steel flanges, steel values, temperature service applications-high, year date, Flanges/fittings/valves/parts--specifications, High-temperature service applications--steel bolting applications, Pressure vessel steel bars--specifications, Steel bolting materials--specifications, Udimet alloy
Doplňujúce informácie
| 1. Scope | ||||||||
|
1.1 This specification covers four grades of bolting materials with ten classes of yield strength ranging from 50 to 120 ksi [345 to 827 MPa] for use in high-temperature service such as fasteners for pressure vessel and valve flanges. The material requires special processing and is not intended for general purpose applications. The term “bolting material,” as used in this specification, covers rolled, forged, or hot-extruded bars; bolts, nuts, screws, washers, studs, and stud bolts. Headed bolts and rolled threads may be supplied. Note 1—Other bolting materials are covered by Specification A 193/A 193M and Specification A 437/A 437M. 1.2 Supplementary Requirement S 1 of an optional nature is provided. This shall apply only when specified by the purchaser in the order. 1.3 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. 1.4 The values stated in either SI or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. ^REFERENCE:ASTM Standards: A 193/A 193M Specification for Alloy-Steel and Stainless Steel Bolting Materials for High Temperature or High Pressure Service and Other Special Purpose Applications A 437/A 437M Specification for Alloy-Steel Turbine-Type Bolting Material Specially Heat Treated for High-Temperature Service A 962/A 962M Specification for Common Requirements for Steel Fasteners or Fastener Materials, or Both, Intended for Use at Any Temperature from Cryogenic to the Creep Range E 139 Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials F 1470 Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
||||||||
| 2. Referenced Documents | ||||||||
|
Doporučujeme:
