Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe for High-Temperature Service
Automaticky preložený názov:
Štandardné špecifikácie pre Electric - Fusion - zvárané Austenitická chrómniklová legovanej ocele rúrka pre High - prevádzkovej teploty
NORMA vydaná dňa 10.3.2001
Označenie normy: ASTM A358/A358M-00
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.3.2001
Kód tovaru: NS-2205
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
arc welded steel pipe, austenitic stainless steel, chromium-nickel steel, fusion welded steel pipe, high temperature application, steel pipe, temperature service applications, high, welded steel pipe, ICS Number Code 23.040.10 (Iron and steel pipes)
1. Scope | ||||||||||||
1.1 This specification covers electric-fusion-welded austenitic chromium-nickel alloy steel pipe suitable for corrosive or high-temperature service, or both. Note 1--The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as "nominal diameter," "size," and "nominal size." <>1.2 This specification covers nineteen grades of alloy steel as indicated in . The selection of the proper alloy and requirements for heat treatment shall be at the discretion of the purchaser, dependent on the service conditions to be encountered. 1.3 Five classes of pipe are covered as follows: 1.3.1 Class 1--Pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed. 1.3.2 Class 2--Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required. 1.3.3 Class 3--Pipe shall be single welded by processes employing filler metal in all passes and shall be completely radiographed. 1.3.4 Class 4--Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition of filler metal (see 6.2.2.1and 6.2.2.2 ). 1.3.5 Class 5--Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed. 1.4 Supplementary requirements covering provisions ranging from additional testing to formalized procedures for manufacturing practice are provided. Supplementary Requirements S1 through S6 are included as options to be specified when desired. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order. |
||||||||||||
2. Referenced Documents | ||||||||||||
|
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2025-03-13 (Počet položiek: 2 232 199)
© Copyright 2025 NORMSERVIS s.r.o.