Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM A307-12

Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength

Automaticky preložený názov:

Štandardné špecifikácie pre Skrutky z uhlíkovej ocele , skrutky a závitové tyče 60 & # x2009 ; 000 PSI Pevnosť v ťahu

NORMA vydaná dňa 1.12.2012

Jazyk
Prevedenie	Online zabezpečené PDF - 77.00 €
Dostupnosť	SKLADOM
Cena	77.00 € bez DPH
77.00 €

Informácie o norme:

Označenie normy: ASTM A307-12
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2012
Kód tovaru: NS-1955
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM A307-12 :

Keywords:

all thread rod, bolts, carbon steel, steel, studs, threaded rod, ICS Number Code 21.060.10 (Bolts, screws, studs)

Doplňujúce informácie

1. Scope

1.1 This specification² covers the chemical and mechanical requirements of two grades of carbon steel bolts and studs in sizes ¹/₄ in. through 4 in. The fasteners are designated by “Grade” denoting tensile strength and intended use, as follows:

Grade

Description

Grade A

Bolts, studs, and threaded rod having a minimum tensile strength of 60 ksi and intended for general applications,

Grade B

Bolts, studs, and threaded rod^A having a tensile strength of 60 to 100 ksi and intended for flanged joints in piping systems with cast iron flanges, and

Grade C

Replaced by Specification F1554 Gr.36

1.2 This specification does not cover requirements for machine screws, thread cutting/forming screws, mechanical expansion anchors or similar externally threaded fasteners.

1.3 Suitable nuts are covered in Specification A563. Unless otherwise specified, the grade and style of nut for each grade of fastener, of all surface finishes, shall be as follows:

Fastener Grade and Size

Nut Grade and Style^A

A ¹/₄ to 1¹/₂ in.

A, hex

A over 1¹/₂ to 4 in.

A, heavy hex

B, ¹/₄ to 4 in.

A, heavy hex

1.4 The values stated in inch-pound units are to be regarded as the standard.

1.5 Supplementary Requirement S1 of an optional nature is provided, which describes additional restrictions to be applied when bolts are to be welded. It shall apply only when specified in the inquiry, order, and contract.

1.6 Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein.

2. Referenced Documents

B?18.24	Part Identifying Number (PIN) Code System Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.
F1470-24	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
F788/F788M-20(2025)	Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series
F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
B695-21	Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
A751-25	Standard Test Methods and Practices for Chemical Analysis of Steel Products
A706/A706M-26a	Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement (Includes all amendments and changes 10/6/2026).
A563-15	Standard Specification for Carbon and Alloy Steel Nuts
B18.31.3	Threaded Rods (Inch Series)
F2329-13	Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
B?1.1	Unified Screw Threads Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
B?18.2.1	Square and Hex Bolts and Screws
F1554-20	Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength
F1789-26a	Standard Terminology for F16 Mechanical Fasteners (Includes all amendments and changes 10/19/2026).

Odporúčame:

EviZak - všetky zákony vrátane ich evidencie na jednom mieste

Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !

Chcete vedieť viac informácii ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.