Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM A307-03

Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength

Automaticky preložený názov:

Štandardné špecifikácie pre uhlíkovej ocele skrutiek a svorníkov, 60 000 PSI pevnosti v ťahu

NORMA vydaná dňa 1.10.2003

Jazyk
Prevedenie	Online zabezpečené PDF - 74.50 € Tlačené - 74.50 €
Dostupnosť	SKLADOM
Cena	74.50 € bez DPH
74.50 €

Informácie o norme:

Označenie normy: ASTM A307-03
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2003
Kód tovaru: NS-1948
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM A307-03 :

Keywords:

bolts, carbon steel, steel, studs, ICS Number Code 21.060.10 (Bolts, screws, studs)

Doplňujúce informácie

1. Scope

1.1 This specification covers the chemical and mechanical requirements of three grades of carbon steel bolts and studs in sizes 1/4 in. (6.35 mm) through 4 in. (104 mm). The fasteners are designated by "Grade" denoting tensile strength and intended use, as follows:

Grade	Description

Grade A	Bolts and studs having a minimum tensile strength of 60 ksi (414 MPa) and intended for general applications,
Grade B	Bolts and studs having a tensile strength of 60 to 100 ksi (414 to 690 MPa) and intended for flanged joints in piping systems with cast iron flanges, and
Grade C	Nonheaded anchor bolts, either bent or straight, having properties conforming to Specification A 36 (tensile strength of 58 to 80 ksi (400 to 550 MPa)) and intended for structural anchorage purposes.

1.1.1 The term studs includes stud stock, sometimes referred to as threaded rod.

1.2 This specification does not cover requirements for machine screws, thread cutting/forming screws, mechanical expansion anchors or similar externally threaded fasteners.

1.3 Suitable nuts are covered in Specification A 563. Unless otherwise specified, the grade and style of nut for each grade of fastener, of all surface finishes, shall be as follows:

Nuts of other grades and styles having specified proof load stresses (Specification A 563, Table 3) greater than the specified grade and style of nut are also suitable.

Fastener Grade and Size	Nut Grade and Style
A, C, 1/4 to 1 1/2 in.	A, hex
A, C, over 1 1/2 to 4 in.	A, heavy hex
B, 1/ 4 to 4 in.	A, heavy hex

1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.5 Supplementary Requirement S1 of an optional nature is provided, which describes additional restrictions to be applied when bolts are to be welded. It shall apply only when specified in the inquiry, order, and contract.

2. Referenced Documents

B?18.24	Part Identifying Number (PIN) Code System Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.
F1470-24	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
F788/F788M-20(2025)	Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series
F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
B695-21	Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
A751-25	Standard Test Methods and Practices for Chemical Analysis of Steel Products
A706/A706M-26	Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
A563-15	Standard Specification for Carbon and Alloy Steel Nuts
B18.31.3	Threaded Rods (Inch Series)
F2329-13	Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
B?1.1	Unified Screw Threads Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
B?18.2.1	Square and Hex Bolts and Screws
F1554-20	Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength
F1789-26	Standard Terminology for F16 Mechanical Fasteners

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.