Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes (Includes all amendments And changes 4/10/2024).
NORMA vydaná dňa 1.3.2023
Označenie normy: ASTM A249/A249M-18a(2023)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2023
Kód tovaru: NS-1135557
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
austenitic stainless steel, boiler tubes, condenser tube, heat exchanger tube, high temperature applications, N08800, N08810, N08811, steel tube, superheater tubes, temperature service applications, high, welded steel tube and heavily cold worked (HCW) tubes,, ICS Number Code 23.040.10 (Iron and steel pipes)
1. Scope | ||||||||||||||||||
1.1?This specification1.2?Grades TP304H, TP309H, TP309HCb, TP310H, TP310HCb, TP316H, TP321H, TP347H, and TP348H are modifications of Grades TP304, TP309S, TP309Cb, TP310S, TP310Cb, TP316, TP321, TP347, and TP348, and are intended for high-temperature service such as for superheaters and reheaters. 1.3?The tubing sizes and thicknesses usually furnished to this specification are 1/8?in. [3.2 mm] in inside diameter to 12 in. [304.8 mm] in outside diameter and 0.015 to 0.320 in. [0.4 to 8.1 mm], inclusive, in wall thickness. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification. 1.4?Mechanical property requirements do not apply to tubing smaller than 1/8?in. [3.2 mm] in inside diameter or 0.015 in. [0.4 mm] in thickness. 1.5?Optional supplementary requirements are provided and, when one or more of these are desired, each shall be so stated in the order. 1.6?The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the M designation of this specification is specified in the order. 1.7?The following safety hazards caveat pertains only to the test method described in the Supplementary Requirements of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.