Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM A217/A217M-20
Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service
NORMA vydaná dňa 1.5.2020
Informácie o norme:
Označenie normy: ASTM A217/A217M-20
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2020
Kód tovaru: NS-992980
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM A217/A217M-20 :
Keywords:
alloy steel, high temperature, martensitic stainless steel, pressure containing, steel castings,, ICS Number Code 77.140.80 (Iron and steel castings)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||
|
1.1 This specification2 covers martensitic stainless steel and alloy steel castings for valves, flanges, fittings, and other pressure-containing parts (Note 1) intended primarily for high-temperature and corrosive service (Note 2). 1.2 One grade of martensitic stainless steel and nine grades of ferritic alloy steel are covered. Selection will depend on design and service conditions, mechanical properties, and the high-temperature and corrosion-resistant characteristics (Note 3). Note 1: Carbon steel castings for pressure-containing parts
are covered by Specification A216/A216M. Low alloy quench-and-tempered
grades equivalent to Specification A217/A217M grades may be found in both
Specifications A352/A352M and
A487/A487M.
Note 2: The grades covered by this specification represent
materials that are generally suitable for assembly with other
castings or wrought steel parts by fusion welding. It is not
intended to imply that these grades possess equal degrees of
weldability; therefore, it is the responsibility of the purchaser
to establish for himself a suitable welding technique. Since these
grades possess varying degrees of suitability for high-temperature
and corrosion-resistant service, it is also the responsibility of
the purchaser to determine which grade shall be furnished, due
consideration being given to the requirements of the applicable
construction codes.
Note 3: The committee formulating this specification has
included nine grades of materials that are considered to represent
basic types of ferritic alloy steels suitable for valves, flanges,
fittings, and other pressure-containing parts. Additional alloy
steels that may better fulfill certain types of service will be
considered for inclusion in this specification by the committee as
the need becomes apparent.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||
|
Odporúčame:
EviZak - všetky zákony vrátane ich evidencie na jednom mieste
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
