Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM A1035/A1035M-15
Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement
Automaticky preložený názov:
Štandardné špecifikácie pre deformované a Plain , nízkouhlíkových , chróm, tyčové ocele pre vystuženie betónu
NORMA vydaná dňa 1.7.2015
Informácie o norme:
Označenie normy: ASTM A1035/A1035M-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2015
Kód tovaru: NS-613215
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM A1035/A1035M-15 :
Keywords:
concrete reinforcement, deformations (protrusions), low-carbon, chromium steel bars,, ICS Number Code 77.140.15 (Steels for reinforcement of concrete)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||
|
1.1 This specification covers deformed and plain low-carbon, chromium, steel bars, in cut lengths and coils for concrete reinforcement. These bars are furnished in three alloy types depending on the chromium range content. The standard sizes and dimensions of deformed bars and their number designations are given in Table 1.1.2 Bars are of two minimum yield strength levels as defined in 9.2: namely, 100 000 psi [690 MPa], and 120 000 psi [830 MPa] designated as Grade 100 [690] and Grade 120 [830], respectively. 1.3 Bars are furnished to three different chemical compositions, designated as Alloy Type CL, CM, and CS. Chemical compositions are shown in Table 2. 1.4 Plain bars, in sizes up to and
including 2.25 in. [57.2 mm] 21/2 in.
[63.5 mm] in diameter in coils and cut lengths, when ordered shall
be furnished under this specification in Grade 100 [690] and Grade
120 [830]. For ductility properties (elongation and bending), test
provisions of the nearest smaller nominal diameter deformed bar
size shall apply. Requirements providing for deformations and
marking shall not be applicable.
Note 1: Welding of the material in this specification should
be approached with caution since no specific provisions have been
included to enhance its weldability. When this steel is to be
welded, a welding procedure suitable for the chemical composition
and intended use or service should be used.
1.5 Requirements for alternate bar sizes are presented in Annex A1. The requirements in Annex A1 only apply when specified by the purchaser (see 4.2.3). 1.6 A supplementary requirement (S1) is provided for use where bend testing of bar sizes Nos. 14 and 18 [43, 57], and bar sizes Nos. 40, 50, and 60 in Annex A1, is required by the purchaser. The supplementary requirement applies only when specified in the purchase order. 1.7 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.8 This specification is applicable for orders in either inch-pound units (as Specification A1035) or in SI units (as Specification A1035M). 1.9 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. |
||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
