Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM A1034/A1034M-10a(2015)
Standard Test Methods for Testing Mechanical Splices for Steel Reinforcing Bars (Includes all amendments And changes 7/24/2023).
Automaticky preložený názov:
Štandardné testovacie metódy pre skúšanie mechanických spojok pre oceľové armovacích prútov
NORMA vydaná dňa 1.12.2015
Informácie o norme:
Označenie normy: ASTM A1034/A1034M-10a(2015)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2015
Kód tovaru: NS-622389
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM A1034/A1034M-10a(2015) :
Keywords:
bar splicing, mechanical splices, reinforced concrete, reinforcing bars, reinforcing bar testing,, ICS Number Code 77.140.50 (Flat steel products and semi-products)
Doplňujúce informácie
| Significance and Use | ||||||||||||||||
|
5.1 Significance: 5.1.1 The bar-splice assembly test specimen shall closely represent the mechanical splice used in practice. The behavior of the bar-splice assembly embedded in concrete, however, may differ from its behavior during testing where it is not embedded in concrete. 5.2 Usefulness: 5.2.1 Testing of mechanical splices for reinforcing bars shall establish the behavior of the bar-splice assembly under the loading conditions described herein for the various test methods to determine the acceptability of the mechanical splice for use in reinforced concrete structural members under specific design criteria. 5.3 Interpretation of Test Results: 5.3.1 Similar or better performance of mechanical splices installed in structural members shall be expected only if materials and methods of assembly are similar to the materials and methods used in the tests. |
||||||||||||||||
| 1. Scope | ||||||||||||||||
|
1.1 These test methods cover the testing of mechanical splices for reinforcing bars. The various tests herein described can be specified in total or individually. 1.2 The test methods herein described are applicable to any type of mechanical splice manufactured to join steel reinforcing bars of any grade (specified minimum yield strength), uncoated or coated. 1.3 This standard describes only the methods for testing mechanical splices for steel reinforcing bars, but does not quantify the parameters for testing nor acceptance criteria, which must be specified. Note 1: Various code-writing bodies specify various
parameters, such as test loads, number of cycles and test
temperature, for testing.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||
|
Odporúčame:
Aktualizácia zákonov
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
