Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F2946-12

Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes

Automaticky preložený názov:

Štandardné špecifikácie pre PVC Hub a elastomérové tesnenia (tesnenia), T spoj pre spojenie Plastová rúrka na INSITU potrubia a šácht

NORMA vydaná dňa 1.8.2012

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 60.90 € Tlačené - 60.90 €
Dostupnosť	SKLADOM
Cena	60.90 € bez DPH
60.90 €

Informácie o norme:

Označenie normy: ASTM F2946-12
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.8.2012
Kód tovaru: NS-54770
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Těsnění pro trubkové a hadicové spoje

Anotácia textu normy ASTM F2946-12 :

Keywords:
elastomeric seal, rubber gasket, service connection, sewer tap, watertight seal, ICS Number Code 23.040.80 (Seals for pipe and hose assemblies)

Doplňujúce informácie


1. Scope
1.1 This specification covers the minimum performance and material requirements for a three piece tee connector for connection between plastic pipe and insitu pipes, manholes and wastewater structures in sanitary and storm sewer applications. 1.1.1 The three piece seal system consists of a 4 through 30-in. PVC (polyvinyl chloride) hub pipe, an elastomeric seal (gasket) and a mechanical band (Fig. 1). The system is installed in either a bored or cast hole opening in the host pipe or structure to a specific dimension that corresponds to the combined diameter of the PVC pipe outside diameter/tolerance and the elastomeric seal thickness. FIG. 1 Three-Piece Sealing System (Connector) 1.2 These tee connectors are designed to provide a non-pressure (gravity flow) watertight connection between the incoming pipe and an insitu pipe or manhole/structure to the limits defined in this standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section
F412-23	Standard Terminology Relating to Plastic Piping Systems
D3034-23	Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D2665-20	Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
A493-23	Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
D1785-21a	Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 (Includes all amendments and changes 10/8/2021).
D1566-21a	Standard Terminology Relating to Rubber (Includes all amendments and changes 11/10/2021).
A666-23	Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
C822-21	Standard Terminology Relating to Concrete Pipe and Related Products
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F2487-21	Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines
C900	Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 in. Through 12 in. (100 mm Through 300 mm), for Water Transmission and Distribution
F679-21	Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings
F1417-11A(2019)e1	Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air (Includes all amendments and changes 5/13/2020).
C923-18	Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals