Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F2764/F2764M-11ae2 1.5.2011 náhľad

Doplňujúce informácie

ASTM F2764/F2764M-11ae2

Standard Specification for 30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications (Includes all amendments And changes 9/12/2016).

Automaticky preložený názov:

Štandardné špecifikácie pre 30-60 palcov [750 - 1500 mm] Polypropylén (PP), Triple Wall rúrky a tvarovky pre netlakovej splašková voda Aplikácie

NORMA vydaná dňa 1.5.2011

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 69.50 € Tlačené - 69.50 €
Dostupnosť	SKLADOM
Cena	69.50 € bez DPH
69.50 €

Informácie o norme:

Označenie normy: ASTM F2764/F2764M-11ae2
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2011
Kód tovaru: NS-54500
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Kanalizační systémy

Anotácia textu normy ASTM F2764/F2764M-11ae2 :

Keywords:
fittings, interior liner, exterior liner, PP, pipe, polypropylene, profile wall, sanitary sewer, ICS Number Code 91.140.80 (Drainage systems)

Doplňujúce informácie

1. Scope

1.1 This specification covers requirements and test methods for triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 30 to 60 in. [750 to 1600 mm].

1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.

1.3 This specification covers pipe and fittings with an essentially smooth interior wall, an essentially smooth exterior wall and an annular corrugated profile middle wall (1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

F2136-18(2024)	Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe
D2321-20	Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
LRFD, Section 12	AASHTO LRFD Bridge Design Specifications Section 12 Buried Structures and Tunnel Liners
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
MIL-STD-129	Marking for Shipment and Storage
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D2990-17	Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D3212-21	Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3895-19	Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
D4101-24	Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
D4218-20	Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
D6992-16(2023)	Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
F412-23	Standard Terminology Relating to Plastic Piping Systems
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
NCHRP Report 631
A666-23	Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
D256-23e1	Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics (Includes all amendments and changes 4/7/2023).
D578/D578M-23	Standard Specification for Glass Fiber Strands
D618-21	Standard Practice for Conditioning Plastics for Testing
D638-22	Standard Test Method for Tensile Properties of Plastics
D790-17	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238-23a	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).
D1505-18	Standard Test Method for Density of Plastics by the Density-Gradient Technique
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
F2736-13	Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe