Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F2619/F2619M-13 1.12.2013 náhľad

Doplňujúce informácie

ASTM F2619/F2619M-13

Standard Specification for High-Density Polyethylene (PE) Line Pipe

Automaticky preložený názov:

Štandard Specification pre High-polyetylénu (PE) potrubné rúry

NORMA vydaná dňa 1.12.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 76.90 € Tlačené - 76.90 €
Dostupnosť	SKLADOM
Cena	76.90 € bez DPH
76.90 €

Informácie o norme:

Označenie normy: ASTM F2619/F2619M-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2013
Kód tovaru: NS-54251
Počet strán: 13
Približná hmotnosť: 39 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty

Anotácia textu normy ASTM F2619/F2619M-13 :

Keywords:
gas, gas gathering, LVP, multiphase, oil, oilfield, PE fittings, PE line pipe, PE pipe, plastic pipe, polyethylene fittings, polyethylene line pipe, polyethylene pipe, water, ICS Number Code 23.040.20 (Plastic pipes)

Doplňujúce informácie

1. Scope

1.1 This specification covers requirements and test methods for high-density polyethylene (PE) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.

1.1.1 For the purposes of this specification, high-density polyethylene material is Specification D3350 density cell classification 3 or higher. This specification does not cover materials having Specification D3350 density cell classification less than 3 such as medium or low density polyethylene materials.

1.1.2 See Specification D2513 for polyethylene pipe and fittings intended for use in the distribution of natural gas, or for use with liquefied petroleum gas.

1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
FED-STD-123G	Federal Standard Marking for Shipment (Civil Agencies)
Military Standard 129P	Standard Practice--Military Marking for Shipment and Storage
PPI TR-3	Policies and Procedures for Developing Hydrostatic Design Basis (HDB), Pressure Design Basis (PDB), Strength Design Basis (SDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825, Irving, TX 75062, http://www.plasticpipe.org.
PPI TR-4	Listing of Hydrostatic Design Basis (HDB), Strength Design Basis (SDB), Pressure Design Basis (PDB) and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe
F1973-21	Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
CSA Z662	Oil and Gas Pipeline Systems Available from Canadian Standards Association (CSA), 5060 Spectrum Way, Mississauga, ON L4W 5N6, Canada, http://www.csa.ca.
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2683-20	Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
D4218-20	Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
F1055-16a(2022)	Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing (Includes all amendments and changes 11/8/2022).
F1473-23	Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins
F2206-19	Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE)
CFR 49 Part 192	Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards Available from U.S. Department of Transportation, Transportation Safety Institute, Pipeline Safety Division, PO Box 25082, Oklahoma City, OK 73125-5050.
Federal Register Vol. 71,	No. 50, March 15, 2006
D2290-19a	Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe (Includes all amendments and changes 9/12/2019).
D3261-24	Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1603-20	Standard Test Method for Carbon Black Content in Olefin Plastics
D2513-20	Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
D2837-22	Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
D638-22	Standard Test Method for Tensile Properties of Plastics
D1238-23a	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).
F412-23	Standard Terminology Relating to Plastic Piping Systems
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure