Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F2160-10

Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD)

Automaticky preložený názov:

Štandardné špecifikácie pre pevnou stenou s vysokou hustotou (HDPE) Conduit na ovládané vonkajším priemerom (OD) Na základe

NORMA vydaná dňa 1.4.2010

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 69.60 € Tlačené - 69.60 €
Dostupnosť	SKLADOM
Cena	69.60 € bez DPH
69.60 €

Informácie o norme:

Označenie normy: ASTM F2160-10
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2010
Kód tovaru: NS-53033
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Instalační trubky pro elektrické vedení

Anotácia textu normy ASTM F2160-10 :

Keywords:
conduit, polyethylene, true size, True size, Conduits--specifications, Ducts/duct liners, High-density polyethylene (HDPE), Nonpressure piping--specifications, Polyethylene (PE)--specifications, Polyethylene (PE) conduit, ICS Number Code 29.120.10 (Conduits for electrical purposes)

Doplňujúce informácie

1. Scope

1.1 This specification covers material, dimensional, workmanship and performance requirements for polyethylene conduit, duct and innerduct manufactured for use in a non- pressure application with communication, CATV, or power wire and cables.

1.2 HDPE conduit meeting the requirements of this standard shall be made as OD controlled solid wall, with or without internal or external ribs. The sizing shall be Iron Pipe Size (IPS) with noted exceptions in tables. The internal or external surface may contain a coextruded layer provided the finished conduit meets the product requirements of this specification.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

2. Referenced Documents

D1505-18	Standard Test Method for Density of Plastics by the Density-Gradient Technique
F1473-23	Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins
D4883-18	Standard Test Method for Density of Polyethylene by the Ultrasound Technique
D1238-23a	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).
D638-22	Standard Test Method for Tensile Properties of Plastics
D2837-22	Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D1693-21	Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
D618-21	Standard Practice for Conditioning Plastics for Testing
D790-17	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
F412-23	Standard Terminology Relating to Plastic Piping Systems
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)