Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F1960-15

Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) Tubing

Automaticky preložený názov:

Štandardné špecifikácie pre studenú Kovanie expanziu PEX Posilnenie krúžky pre použitie s sieťovaný polyetylén ( PEX ) Tubing

NORMA vydaná dňa 1.4.2015

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 69.50 € Tlačené - 69.50 €
Dostupnosť	SKLADOM
Cena	69.50 € bez DPH
69.50 €

Informácie o norme:

Označenie normy: ASTM F1960-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2015
Kód tovaru: NS-588547
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Fitinky z plastické hmoty

Anotácia textu normy ASTM F1960-15 :

Keywords:
cold expansion fittings, cross-linked polyethylene, hot and cold water distribution, PEX, PEX reinforcing rings,, ICS Number Code 23.040.45 (Plastics fittings)

Doplňujúce informácie

1. Scope

1.1 This specification covers cold expansion fittings and cross-linked (PEX) reinforcing rings for use with cross-linked polyethylene (PEX) plastic tubing in ³/₈ , ¹/₂ , ⁵/₈ , ³/₄ , 1, 1¹/₄ , 1¹/₂ in. 2, 2¹/₂ , and 3 in. nominal diameters that meet the requirements of Specifications F876 and F877. These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180°F (82°C). The system is comprised of a PEX reinforcing ring and a cold expansion fitting. Included are the requirements for materials, workmanship, dimensions, and markings to be used on the fitting components. The components covered by this specification are intended for use in residential and commercial, hot and cold, potable water distribution systems as well as sealed central heating, including under-floor-heating systems.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D1505-18	Standard Test Method for Density of Plastics by the Density-Gradient Technique
B967/B967M-18(2023)	Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2765-16(2024)	Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
D3035-22	Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
D6394-21a	Standard Classification System for and Basis for Specification for Sulfone Plastics (SP) (Includes all amendments and changes 5/13/2021).
F412-23	Standard Terminology Relating to Plastic Piping Systems
F876-24	Standard Specification for Crosslinked Polyethylene (PEX) Tubing
F877-24	Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
B1.20	Pipe Threads General Purpose Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org
B16.18	Cast Copper Alloy Solder Joint Pressure Fittings
B584-22	Standard Specification for Copper Alloy Sand Castings for General Applications
B371/B371M-19	Standard Specification for Copper-Zinc-Silicon Alloy Rod
A351/A351M-18e1	Standard Specification for Castings, Austenitic, for Pressure-Containing Parts (Includes all amendments and changes 8/27/2019).
B16/B16M-19	Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B140/B140M-22	Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
B62-17	Standard Specification for Composition Bronze or Ounce Metal Castings
B75/B75M-20	Standard Specification for Seamless Copper Tube
B283/B283M-22	Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
B453/B453M-19	Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes
B16.22	Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
B927/B927M-23	Standard Specification for Brass Rod, Bar, and Shapes
NSF 61	for Drinking Water System Components-Health Effects
NSF 14	for Plastic Piping Components and Related Materials Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.