Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM B580-79(2009) 15.4.2009 náhľad

Doplňujúce informácie

ASTM B580-79(2009)

Standard Specification for Anodic Oxide Coatings on Aluminum

Automaticky preložený názov:

Štandardné špecifikácie pre anodickú Oxide povlakov na hliník

NORMA vydaná dňa 15.4.2009

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 61.10 € Tlačené - 61.10 €
Dostupnosť	SKLADOM
Cena	61.10 € bez DPH
61.10 €

Informácie o norme:

Označenie normy: ASTM B580-79(2009)
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.4.2009
Kód tovaru: NS-7263
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM B580-79(2009) :

Keywords:
Aluminum alloys--specifications, Aluminum alloys (anodic coatings)--specifications, Aluminum coatings--specifications, Anodic coatings--Al/Al alloys), ICS Number Code 25.220.20 (Surface treatment)

Doplňujúce informácie

1. Scope

1.1 This specification covers requirements for electrolytically formed porous oxide coatings on aluminum and aluminum alloy parts in which appearance, abrasion resistance, electrical properties, and protection against corrosion are important. Nonporous, barrier layer anodic coatings used for electrical capacitors are not covered. Seven types of coatings as shown in Table 1 are provided. Definitions and typical examples of service conditions are provided in Appendix X1.

Note 1—It is recognized that uses exist in which modifications of the coatings covered by this specification may be required. In such cases the particular properties desired by the purchaser should be the subject of agreement between the purchaser and the manufacturer.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

TABLE 1 Anodic Coatings Descriptions

Note—Hard coatings may vary in thickness from 12 μm to more than 100 μm. If the thickness of Type A is not specified, it shall be 50 μm min. Type A coatings will not be sealed unless so specified.

Type	Coating (Industry) Description	Minimum Film Thickness (μm)
A	Engineering Hard Coat	50
B	Architectural Class I	18
C	Architectural Class II	10
D	Automotive—Exterior	8
E	Interior—Moderate Abrasion	5.0
F	Interior—Limited Abrasion	3
G	Chromic Acid	1

2. Referenced Documents

E429-78(1991)E01	Test Method for Measurement and Calculation of Reflecting Characteristics of Metallic Surfaces Using Integrating Sphere Instruments (Withdrawn 1996)
D658-91	Standard Test Method for Abrasion Resistance of Organic Coatings by Air Blast Abrasive (Withdrawn 1996)
B137-95(2021)	Standard Test Method for Measurement of Coating Mass Per Unit Area on Anodically Coated Aluminum
B136-23	Standard Test Method for Measurement of Stain Resistance of Anodic Coatings on Aluminum
B117-19	Standard Practice for Operating Salt Spray (Fog) Apparatus
B110-45(1973)	Method of Dielectric Strength of Anodically Coated Aluminum (Withdrawn 1981)
MIL-STD-414	Sampling Procedures and Tables for Inspection by Variables for Percent Defective
B602-21	Standard Guide for Attribute Sampling of Metallic and Inorganic Coatings
B538-70	Method of Fact (Ford Anodized Aluminum Corrosion Test) (Withdrawn 1986)
B487-20	Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section
B457-67(1998)	Standard Test Method for Measurement of Impedance of Anodic Coatings on Aluminum
B244-09(2021)	Standard Test Method for Measurement of Thickness of Anodic Coatings on Aluminum and of Other Nonconductive Coatings on Nonmagnetic Basis Metals with Eddy-Current Instruments
E430-23	Standard Test Methods for Measurement of Gloss of High-Gloss Surfaces by Abridged Goniophotometry
MIL-STD-105	Sampling Procedures and Tables for Inspection by Attributes Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
B368-21	Standard Test Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test)

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.