Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F594-09(2015) 1.9.2015 náhľad

Doplňujúce informácie

ASTM F594-09(2015)

Standard Specification for Stainless Steel Nuts

Automaticky preložený názov:

Štandardné špecifikácie pre nehrdzavejúcej ocele matice

NORMA vydaná dňa 1.9.2015

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.00 € Tlačené - 70.00 €
Dostupnosť	SKLADOM
Cena	70.00 € bez DPH
70.00 €

Informácie o norme:

Označenie normy: ASTM F594-09(2015)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.9.2015
Kód tovaru: NS-619069
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Matice

Anotácia textu normy ASTM F594-09(2015) :

Keywords:
ICS Number Code 21.060.20 (Nuts)

Doplňujúce informácie

Significance and Use

15.1 For the purposes of determining compliance with the specified limits for properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.

1. Scope

1.1 This specification covers the requirements for stainless steel nuts 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

1.2 Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening.

Group

Alloys^A

Condition^B

304, 305, 304L
384, 18–9LW, 302HQ^C

(CW)

cold worked^D

316, 316L

(CW)

cold worked^D

321, 347

(CW)

cold worked^D

430^E

(CW)

cold worked^D

410^F

(H)

hardened and tempered

431

(H)

hardened and tempered

630

(AH)

aged hardened

1.3 Supplementary requirements of an optional nature are provided, applicable only when agreed upon by the manufacturer and the purchaser at the time of the inquiry and order.

1.4 Suitable bolts, hex cap screws, and studs for use with nuts included in this specification are covered by Specification F593. Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F593 and shall be of the same alloy group.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

	Square and Hex Nuts
F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
F593-22	Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
A582/A582M-22	Standard Specification for Free-Machining Stainless Steel Bars
A564/A564M-19a	Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes (Includes all amendments and changes 4/2/2021).
A555/A555M-23	Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods
A493-23	Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
A380-06	Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
A342/A342M-21	Standard Test Methods for Permeability of Weakly Magnetic Materials
A262-15(2021)	Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
B1.1	Unified Inch Screw Threads
E1470-92(1998)	Standard Test Method for Characterization of Proteins by Electrophoretic Mobility
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
D3951-18(2023)	Standard Practice for Commercial Packaging
A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.