Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM D7064/D7064M-08(2013) 1.12.2013 náhľad

Doplňujúce informácie

ASTM D7064/D7064M-08(2013)

Standard Practice for Open-Graded Friction Course (OGFC) Mix Design

Automaticky preložený názov:

Štandardné praktiky pre Open-triedené trenie kurz (OGFC) Mix dizajnu

NORMA vydaná dňa 1.12.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 69.80 € Tlačené - 69.80 €
Dostupnosť	SKLADOM
Cena	69.80 € bez DPH
69.80 €

Informácie o norme:

Označenie normy: ASTM D7064/D7064M-08(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2013
Kód tovaru: NS-37465
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Materiály pro stavbu silnic

Anotácia textu normy ASTM D7064/D7064M-08(2013) :

Keywords:
bituminous paving mixtures, mix design, open-graded friction course, surface treatments, ICS Number Code 93.080.20 (Road construction materials)

Doplňujúce informácie

Significance and Use

5.1 The procedure described in this practice is used to design OGFC mixtures that will provide good performance in terms of permeability (tending to reduce hydroplaning and potential for skidding), and durability when subjected to high volumes of traffic.

1. Scope

1.1 This practice covers the mix design of open-graded friction course (OGFC) using the superpave gyratory compactor (SGC) or other suitable forms of compaction. The OGFC mix design is based on the volumetric properties of the mix in terms of air voids, and the presence of stone-on-stone contact. Information found in Guide D6932 should be reviewed before starting the mix design. Where applicable, Specification D3666 should be applied as a minimum for agencies testing and inspecting road and paving materials.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D2419-22	Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
D3203-22	Standard Test Method for Percent Air Voids in Compacted Asphalt Mixtures
D3381-09	Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction
C136-06	Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
C1252-23	Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading)
D3666-16	Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
D4791-19(2023)	Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate
D5821-13(2017)	Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
D6114-97e1	Standard Specification for Asphalt-Rubber Binder
D6373-23	Standard Specification for Performance-Graded Asphalt Binder
D6390-23	Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures
D6752-09	Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method
D6857-09	Standard Test Method for Maximum Specific Gravity and Density of Bituminous Paving Mixtures Using Automatic Vacuum Sealing Method
D6925-23	Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor
D6926-20	Standard Practice for Preparation of Asphalt Mixture Specimens Using Marshall Apparatus
D6932-04	Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Mixtures
C29/C29M-23	Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate
C127-15	Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate (Withdrawn 2024)
C131-06	Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
R 30	Mixture Conditioning of Hot Mix Asphalt (HMA)
T 283	Resistance of Compacted Bituminous Mixture to Moisture-Induced Damage
TRB Synthesis 284
NCAT Report No. 2001-01	Design, Construction, and Performance of New-Generation Open-Graded Friction Courses
D946-09	Standard Specification for Penetration-Graded Asphalt Cement for Use in Pavement Construction
D2041-03	Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures