Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Quality Control of Geosynthetic Clay Liners
NORMA vydaná dňa 1.2.2018
Označenie normy: ASTM D5889/D5889M-18
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.2.2018
Kód tovaru: NS-809981
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Utváření krajiny. Lesnictví
Minerální stavební materiály a produkty
Keywords:
geosynthetic clay liners, geosynthetics, manufacturing quality control, multicomponent GCLs, testing,, ICS Number Code 65.020.40 (Landscaping and silviculture),91.100.15 (Mineral materials and products)
Significance and Use | ||||||||||||||||||||||||||||||||||
4.1 GCLs must be properly manufactured in a manner consistent with a minimum level of quality control as determined by in-house testing of the final product. This practice suggests the types of tests, the methods of the testing, and the minimum testing frequencies. 4.2 It should be clearly recognized that
manufacturers may perform additional tests or at greater frequency
than required in this practice, or both. In this case, the
manufacturer's quality control plan will then take precedence over
this practice. The quoted tests and test methods in Table 1 must appear in the QC plan and
the QC report.
4.3 It should also be recognized that purchasers and installers of GCLs may require additional tests or greater frequencies than called for in this practice, or both. The organization(s) producing such project-specific specification or quality assurance plan should recognize that such requirements are beyond the current state of the practice. If such a request is made by purchasers or installers, they should clearly communicate the requirements to the manufacturer or supplier during the contract decisions in order that disputes do not arise at a subsequent time. |
||||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||||
1.1 This practice covers the manufacturing quality control of geosynthetic clay liners (GCLs), describing types of tests, the proper test methods, and the minimum testing frequencies. 1.2 This practice is intended to aid manufacturers, suppliers, purchasers, and users of GCLs in establishing a minimum level of effort for manufacturing quality control. 1.3 This practice does not address manufacturing quality assurance, product acceptance testing, or conformance testing. These are independent activities taken by organizations other than the GCL manufacturer. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||
|
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-05-15 (Počet položiek: 2 898 636)
© Copyright 2024 NORMSERVIS s.r.o.