Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D5685-11

Standard Specification for ""Fiberglass"" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings

Automaticky preložený názov:

Štandardné špecifikácie pre "sklenených vlákien" (sklenými vláknami vystužený Teplom-živice) Kovanie tlakového potrubia

NORMA vydaná dňa 1.2.2011

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 69.20 € Tlačené - 69.20 €
Dostupnosť	SKLADOM
Cena	69.20 € bez DPH
69.20 €

Informácie o norme:

Označenie normy: ASTM D5685-11
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.2.2011
Kód tovaru: NS-32178
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Fitinky z plastické hmoty

Anotácia textu normy ASTM D5685-11 :

Keywords:
centrifugally cast, compression molded, contact molded, degree of cure, epoxy-resin, filament-wound, furan-resin, glass transition temperature, percent extractable material, polyester-resin, pressure-rating, transfer molded, Centrifugally cast plastic pipe--specifications, Compression-molded plastic specimens, Contact molded pipe/flanges--specifications, Epoxy resin pipe fittings--specifications, Fiberglass pipe--specifications, Filament-wound plastic pipe, Glass-fiber-reinforced (GRP) plastics

Doplňujúce informácie

1. Scope

1.1 This specification covers “fiberglass” (glass-fiber-reinforced thermosetting-resin) fittings for use with filament wound or centrifugally cast fiberglass pipe, or both, in sizes 1 in. through 24 in. for pipe manufactured to Specification D2996 or D2997, or both.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following safety hazard caveat pertains only to the test method portion, Section 7, of this specification:

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1—The term “fiberglass pipe” as described in Section 3 of this specification applies to both reinforced thermosetting resin pipe (RTRP) and reinforced polymer mortar pipe (RPMP).

Note 2—For the purposes of this standard, ploymer does not include natural polymers.

Note 3—There is no known ISO equivalent to this standard.

A1.1.1 This test determines whether the degree of cure of a fiberglass fitting test specimen meets the quality control requirements determined by statistical analysis of typical production products.

2. Referenced Documents

F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
B16.5	Steel Pipe Flanges, Flanged Valves and Fittings Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
D2997-21	Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
D2996-23	Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
D2992-22	Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
D2310-06	Standard Classification for Machine-Made ""Fiberglass"" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
D3567-17(2022)	Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D883-24	Standard Terminology Relating to Plastics
D618-21	Standard Practice for Conditioning Plastics for Testing
D2143-21	Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe
F412-23	Standard Terminology Relating to Plastic Piping Systems
D4024-22	Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges

Podobné normy:

ASTM D3965-11

Historická
1.9.2011

ASTM D5677-05(2010)..

Historická
1.11.2010

ASTM D6041-11

Historická
1.12.2011

ASTM F1201-88(2010)..

Historická
1.5.2010

ASTM F1290-98a(2011)..

Historická
1.2.2011

ASTM F1336-07

Historická
1.5.2007

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.