Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D5677-17

Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines

NORMA vydaná dňa 1.3.2017

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 69.60 € Tlačené - 69.60 €
Dostupnosť	SKLADOM
Cena	69.60 € bez DPH
69.60 €

Informácie o norme:

Označenie normy: ASTM D5677-17
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2017
Kód tovaru: NS-678297
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty
Fitinky z plastické hmoty

Anotácia textu normy ASTM D5677-17 :

Keywords:
beam strength, boil resistance, centrifugally cast, cycling resistance, epoxy resins, filament wound, impact resistance, jet fuel, joint strength, molded,, ICS Number Code 23.040.20 (Plastic pipes),23.040.45 (Plastic fittings)

Doplňujúce informácie

1. Scope

1.1 This specification covers a reinforced plastic pipe and fittings system made from epoxy resin and glass-fiber reinforcement, together with adhesive for joint assembly, intended for service up to 150°F (65.6°C) and 150-psig (1034-kPa) operating pressure and surges up to 275 psig (1896 kPa) in aviation jet turbine fuel lines installed below ground.

1.2 The dimensionless designator NPS has been substituted in this specification for such traditional terms as 1.3 The values stated in inch-pound units are to be regarded as standard. The values in parentheses are for information only.

1.4 The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1: There is no known ISO equivalent to this standard.

2. Referenced Documents

D3241-23ae1	Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (Includes all amendments and changes 1/10/2024).
D3567-17(2022)	Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
	Steel Pipe Flanges and Flanged Fittings Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
D2310-06	Standard Classification for Machine-Made ""Fiberglass"" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D3951-18(2023)	Standard Practice for Commercial Packaging
D5685-19	Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings
F412-23	Standard Terminology Relating to Plastic Piping Systems
F1173-01(2023)	Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications
MIL-T-5624	Turbine Fuel, Aviation, Grades JP-4, JP-5 and JP-5/JP-8 ST Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D381-22	Standard Test Method for Gum Content in Fuels by Jet Evaporation
D883-24	Standard Terminology Relating to Plastics
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1655-23a	Standard Specification for Aviation Turbine Fuels (Includes all amendments and changes 10/11/2023).

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.