Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D5171-15
Standard Test Method for Impact Resistance of Plastic Sew-Through Buttons
Automaticky preložený názov:
Štandardná skúšobná metóda pre odolnosť proti nárazu Plastové Šiť - through Tlačidlá
NORMA vydaná dňa 15.1.2015
Informácie o norme:
Označenie normy: ASTM D5171-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.1.2015
Kód tovaru: NS-615808
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Pokrývky hlavy. Oděvní doplňky. Připevňovací oděvní prostředky
Anotácia textu normy ASTM D5171-15 :
Keywords:
button, impact resistance, strength,, ICS Number Code 61.040 (Headgear. Clothing accessories. Fastening of clothing)
Doplňujúce informácie
| Significance and Use | ||||||
|
5.1 This test method may be used to determine the ability of a button to resist breaking under impact, for example in pressing the end item, which could cause the button to fail. Note 1: In the development of this test method it was found
that the following factors influenced the ability of a button to
resist failure under impact conditions: resin formulation, shape
ligne size, thickness, number and spacing of holes. Buttons may
also pass this test but fail during the pressing of a garment due
to the presence of heat during pressing.
5.1.1 If there are differences of practical significance between the reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate rest results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. 5.2 Test Method D5171 for the determination of the impact resistance of buttons may be used for acceptance testing of commercial shipments of buttons but caution is advisable since information is lacking on precision. |
||||||
| 1. Scope | ||||||
|
1.1 This test method covers the determination of impact resistance of plastic sew-through buttons. 1.2 The values stated in either acceptable metric units or other units shall be regarded separately as standard. The values expressed in each system may or may not be exact equivalents: therefore, each system must be used independently of the other, without combining values in any way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
| 2. Referenced Documents | ||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
